controls in the cockpit vs. which wheels they apply to. FlightGear now
sets /controls/gear/brake-left, /controls/gear/brake-right, and
/controls/gear/brake-parking. It should be up to the FDM to sort out
which wheels under which circumstances are affected by these controls
and ultimately what happens to the physical motion of the aircraft.
places now use sgCartToGeod() instead of rolling their own
approximation. And YASim is now using exactly the same 3D coordinate
system as the rest of FlightGear is.
the core YASim stuff. Mostly cosmetic: whitespace adjustment, dead
code & meaningless comment removal, a little code motion to better
partition the helicopter handling from the original code (no more
giant if() { ... } around the solver). Added a warning to the parser
to try to eliminate the string booleans that crept in.
There should be NO behavioral changes with this checkin.
Here's a new FGSimTurbine module. Changes are:
1. Adds starting and stopping functionality
2. Calculate() now calls other functions, based on the engine's state, which gives more readable code.
Until now turbine engines were always running as long as fuel was available. With this new module the engine defaults to OFF. To start with the engine running, the variable FGEngine::Running must be set to true at sim startup. In FlightGear this is done with --prop:/engines/engine[n]/running=true.
To start the engine (on the ground), first set the starter to ON, i.e. FGEngine::Starter is set to true. In FlightGear this is done by toggling /controls/engines/engine[n]/starter to TRUE. Note that the current FlightGear key binding will not work, as it causes the starter to quit when the key is released. A new key binding is needed, without the mod-up.
When N2 reaches 15% or greater, place the fuel cutoff control to FALSE. This is FGEngine::Cutoff. In FlightGear this is done with /controls/engines/engine[n]/cutoff set to FALSE. The engine will then accelerate to idle. Upon reaching idle, the starter is automatically turned off, and the engine is running. There is presently no FlightGear key binding for the fuel cutoff switch.
To shut off the engine, place the fuel cutoff control to TRUE.
If you shut down the engine in flight it will windmill. To airstart you will need at least 15% N2, just as with a ground start. When you have enough N2, place the cutoff control to FALSE and the engine will restart. Note that if you can't get enough N2 by speeding up, you can get it by using the starter.
The reverser still works, and is controlled in FlightGear with /controls/engines/engine[n]/reverser. With the reverser control on (TRUE), the engine will produce negative thrust in proportion to throttle position, i.e. to get more reverse
thrust, increase throttle.
Here's a new FGSimTurbine module. Changes are:
1. Adds starting and stopping functionality
2. Calculate() now calls other functions, based on the engine's state, which gives more readable code.
Until now turbine engines were always running as long as fuel was available. With this new module the engine defaults to OFF. To start with the engine running, the variable FGEngine::Running must be set to true at sim startup. In FlightGear this is done with --prop:/engines/engine[n]/running=true.
To start the engine (on the ground), first set the starter to ON, i.e. FGEngine::Starter is set to true. In FlightGear this is done by toggling /controls/engines/engine[n]/starter to TRUE. Note that the current FlightGear key binding will not work, as it causes the starter to quit when the key is released. A new key binding is needed, without the mod-up.
When N2 reaches 15% or greater, place the fuel cutoff control to FALSE. This is FGEngine::Cutoff. In FlightGear this is done with /controls/engines/engine[n]/cutoff set to FALSE. The engine will then accelerate to idle. Upon reaching idle, the starter is automatically turned off, and the engine is running. There is presently no FlightGear key binding for the fuel cutoff switch.
To shut off the engine, place the fuel cutoff control to TRUE.
If you shut down the engine in flight it will windmill. To airstart you will need at least 15% N2, just as with a ground start. When you have enough N2, place the cutoff control to FALSE and the engine will restart. Note that if you can't get enough N2 by speeding up, you can get it by using the starter.
The reverser still works, and is controlled in FlightGear with /controls/engines/engine[n]/reverser. With the reverser control on (TRUE), the engine will produce negative thrust in proportion to throttle position, i.e. to get more reverse thrust, increase throttle.
now read the config file out of the individual aircraft directory rather
than the collective Aircraft-yasim/ directory (which is now obsolete.)
This requires a corresponding update of the base package cvs.
The Propeller class ignored negative RPM but still returned a torque
value, which ratcheted up a higher and higher negative RPM until drag
overwhelmed the aircraft.
In reality, the propeller should windmill at a reasonable postive RPM,
introducing a constant drag on the aircraft -- the propeller should
*not* stop unless the plane is flying very slowly. That's a future
project.
I have added a fledgling replay system that records flight data and control
positions during the flight.
I have added an internal command called "replay" which will trigger a replay
of the entire saved flight data set. This could be bound to a keyboard or
menu command, in fact this entire module is screaming for someone to build
a gui to control playback speed, amount of playback, etc.
This is the initial version so there are kinks that still need to be worked
out, please be patient.
Square the normalized direction acceleration for the y and z axes, so
that turbulence predominantly affects pitch.
Bind to the /environment/turbulence/magnitude-norm and
/environment/turbulence/rate-hz properties in FlightGear.
This version handles a zero fuel load better. I found that if you try to consume fuel from an empty tank, with zero fuel flow, the FGEngine::Starved flag alternates
> > Here's a patch to add manual-pitch control to the propeller in YASim. A new
> > control axis "PROPPITCH" is added. Requires "manual-pitch" boolean property
> > in the "propeller" tag.
> >
> > Tags and Properties to add in order to enable:
> >
> > manual-pitch="true"
> >
> > <control-input axis="/controls/engines/engine[0]/propeller-pitch"
> > control="PROPPITCH" src0="0" src1="1" dst0="0.40" dst1="0.80"/>
> >
> > Note that for the time being, excessively low RPM or excessively high RPM is
> > brought undercontrol by a scaling range defined in the control-input tag
> > (see "dst0" and "dst1" properties).
I have attached some revisions for the UIUCModel and some LaRCsim.
The only thing you should need to check is LaRCsim.cxx. The file
I attached is a revised version of 1.5 and the latest is 1.7. Also,
uiuc_getwind.c and uiuc_getwind.h are no longer in the LaRCsim
directory. They have been moved over to UIUCModel.
I split the FGModelPlacement code out into it's own set of source files.
I created two versions of the fgLoad3DModel() routine. One that is
unecumbered by a panelnode dependency and one that is. acmodel.cxx is
the only place that needs to load an aircraft with instrument panels.
model.[ch]xx are now pretty much free to move over into simgear.
loader.[ch]xx should be able to follow closely behind.
This will be a big step towards being able to move the material management
code over into simgear.
scene management code and organizing it within simgear. My strategy is
to identify the code I want to move, and break it's direct flightgear
dependencies. Then it will be free to move over into the simgear package.
- Moved some property specific code into simgear/props/
- Split out the condition code from fgfs/src/Main/fg_props and put it
in it's own source file in simgear/props/
- Created a scene subdirectory for scenery, model, and material property
related code.
- Moved location.[ch]xx into simgear/scene/model/
- The location and condition code had dependencies on flightgear's global
state (all the globals-> stuff, the flightgear property tree, etc.) SimGear
code can't depend on it so that data has to be passed as parameters to the
functions/methods/constructors.
- This need to pass data as function parameters had a dramatic cascading
effect throughout the FlightGear code.
that after a reset or reposition, several FDM variable were not unbound
correctly and left dangling pointing to unallocated memory. This wasn't
a crash type bug, but those properties then had bogus values. This
specifically prevented the turn coordinator gyro modeling from working after
a reset or reposition.
ttStandard is copied from ttBerndt, with the following modifications:
1. All turbulence is diminished within three wingspans of the ground.
2. The horizontal forces are used to calculate the moments, but then
zeroed out so that only the vertical force is actually applied to
the aircraft.
3. The yaw moment is not used.
In fact, the horizontal forces and the yaw moment should be allowed,
but they are extremely rare compared to the vertical force and the
pitch/roll moments. For now, simply zeroing them gives the most
accurate feel.
FGExternalPipe is destructed.) This leaves the name pipe hanging around
even after flightgear exits, but assuming we put the files in /tmp that
shouldn't be a big deal.
ExternalNet interface:
- allows a much more closely coupled execution. A remote network FDM will run
at it's own rate, and maybe a particular data packets will come, maybe it
won't. This makes it very hard to control timing and keep the animation
smooth. There are also cpu scheduling issues with running multiple
processes on a single machine. The linux scheduler by default runs at
100hz. If an FDM process uses a sleep/alarm system to avoid wasting
CPU, it will be forced to run at 100hz, 50hz, 25hz, 20hz, etc. This
makes it *impossible* to serve a display system running at 60hz without
dropping frames.
- the downside is that the FDM process must now run on the same machine as
the master flightgear process.
- NED and UVW are working correctly
- knots is giving true airspeed instead of calibrated airspeed
- mach is not working at all
This desperately needs a trimming routine.
Some more cmall changes to the SimGear header files and removed the
SG_HAVE_NATIVE_SGI_COMPILERS dependancies from FlightGear.
I've added a seperate JSBSim patch for the JSBSim source tree.
really useful unless we simultaneously change the per-iteration deltas
to be smaller. Add another pseudo-tunable to control the speed with
which we change values across iterations. As it turns out, this is
much more effective than the threshold tunable. It does come at the
cost of lower solution performance, however.
