Make a single Cmake value to expose the build type to code, and use
this to default a run-time ‘developer-mode’ property, which can be
over-ridden from the command line.
Use this to drive the different warning levels. Policies subject to
review, especially whether nightly builds should default to
developer mode or not.
There is a Flightgear property called /sim/hitches/winch/automatic-release-angle-deg that can be used to simulate a safety feature built into modern gliders. If the cable angle gets too great during a winch launch, the hook will automatically release the cable. This usually happens when the glider gets almost on top of the winch at the top of the launch without releasing the cable.
Unfortunately winch launching has two separate implementations, one in Nasal for JSBSim, and another one in C++ for YASIM. The YASIM one does not implement this property so I wrote a patch to add this.
As discussed on the mailing list, make this more consistent with JSBsim.
We could still define common locations for these values as well, but
waiting on positive answer to that discussion on the ML.
when active does not touch the way the YASim jet calculates fuel flow, but separates out the afterburning component of thrust, calculates the TSFC of that component and uses the same method of fuel flow calculation for the afterburning component then adds it to the existing fuel flow
When inactive (atsfc doesn't exist or is zero) it just behaves exactly as before
I finally got around to testing this small patch thoroughly, and I'm satisfied that it doesn't affect anything else & works across many different versions (i've been testing it with current as it has changed over the last 7 months)
Change the drag coefficient for fuselages along the Y and Z axes
(i.e. perpendicular to the fuselage's main axis) to use a fixed
value of 0.5. (The value can still be adjusted using the fuselage's
"cy" and "cz" XML attributes.)
For the Y-axis and Z-axis drag on fuselages, YASim originally used
a drag coefficient equal to:
(solver drag factor) * (fuselage length/width ratio)
This value turns out to be way too small for well-streamlined
aircraft, even those with long, narrow fuselages, and especially
so for those with short, stubby fuselages. Such fuselages are
streamlined in the X direction, but not along Y or Z.
0.5 is only a ballpark estimate, but it's reasonably close for the
common case of a fairly long fuselage with a round cross section. For
flat-sided fuselages, a larger value should be used, up to a maximum
of 2 for a slab-sided block. For short fuselages, the value should be
reduced to account for end effects. The fuselage's "cy" and "cz" XML
attributes can be modified to make such adjustments.
This fix won't affect straight flight much, but it should have a strong
impact on some maneuvers. For example, it will make slips more
effective and may make knife-edge flight easier on aerobatic aircraft
which should be capable of it.
Only aircraft which specify version="YASIM_VERSION_32" or newer are
affected.
This commit is in prepartion for the following commit, which is a bug fix for
Issue 1463 (YASim underestimates off-axis forces on fuselages).
Previously the solver would adjust the drag factor for all of an Airplane's
non-Wing Surfaces in one pass, with no attempt to distinguish Fuselage Surfaces
from the Surfaces for Gear and Weights. This makes it difficult to modify how
fuselage drag is calculated while leaving unaffected the drag for landing gear
and external weights.
Now the solver adjusts the drag for an Airplane's fuselages, landing gear, and
external weights in three separate passes. To do this, each Fuselage now has a
list of its Surfaces. The fuselage pass simply iterates through the list of
Fuselages, running through each Fuselage's list of Surfaces.
The Airplane's list of non-Wing Surfaces, "_surfs", is no longer used here, but
there may still be uses of it elsewhere.
Correct handling of fuselage's "midpoint" XML attribute so that the midpoint's
location matches the point assumed by all aircraft developers and YASim docs.
This means the fuselage won't be generated "back-to-front".
Also correct the variation of diameter for tapered fuselages so that both ends
of the fuselage narrow from the midpoint to the endpoints.
Before this, one end was narrowing from the endpoint to the midpoint, the
opposite of what was expected.
These changes affect both weight distribution and the distribution of lateral
aerodynamic forces.
user attribute "version" of the airplane element of the YASim config file
to define the version this config uses.
Example:
<airplane mass="1344" version="YASIM_VERSION_CURRENT">
Initially, the following can be used:
YASIM_VERSION_ORIGINAL - The original version of YASim as implemented up to
FlightGear 3.0.0
YASIM_VERSION_32 - The version of YASim implemented in FlightGear 3.2.x
(and the development version 3.1.x)
YASIM_VERSION_CURRENT - The current and latest version of YASim.
