implicitly correcting for that yet. The plane now makes it to 11000ft on
autopilot *slowly*. I think I'll have to look at the prop parameters
next - altering the diameter and blade angle just slightly can have
quite an effect. If you want to play then try changing the values
prop_diameter and blade_angle in FGNewEngine::init. Keep blade
angle between 20 and 25 (since those are the only values for which
I've entered data and I interpolate between them) and ignore
FGProp1_Blade_Angle since that's an old variable that isn't used. I
really ought to read all the engine and prop parameters from file to
avoid recompilation when tweaking !
the actual air pressure and temperature from the LaRCSim model
instead of assuming that it is at sea level as before. This has
reduced the ceiling from over 60000 ft to about 9000 ft. This is a bit
low (should be around 13 - 14000 ft I think) but I still have some
stuff to do with the engine power correlation and its ignoring the
temperature at the moment so I'm not panicking yet :-)
I've also changed the mixture-power correlation to one from a
published paper since the curve from the IO360 manual seemed to
be a load of rubbish, and didn't have any numbers on the mixture
axis anyway.
I've also knocked the full rich mixture down a touch in line with
Riley Rainey's recommendation, and cleaned up the code a bit.
a) I was compairing feet vs. meter (making the range 3x too. big)
b) I was using the diameter in place of the radius (making the range an
additional 2x too big.)
c) Updated the equation for calculating range to model the weak transmitter
not being picked up at upper altitudes.
We still might need some additional tweaking, but I think we are starting to
get in the right ball park.
is 9 not 8.) Note that the initial altitude setting was placing us way below
the ground, but as it doesn't seem to have caused us problems, it's probably
redundant!
When you tune into a station start at a "random" point in the sequence.
Sped up the words per minute to 13 to which means one sequence per about 4 secs.
This means we get through the whole sequence in about 20 seconds leaving 10
seconds of silence.
joystick input, and then will ignore the actual position of that input
until the user places it in the proper position to match the trimmed position.
At that point the joystick input captures control over the value and the
value will match the joystick position from then on. This is primarily set
up so that the FDM can trim in an initial throttle position.
Added fuel-flow and total fuel to the LaRCSim model. Its still a bit
rough for now but it works, except the engine dosn't stop when fuel runs
out at the moment since there's no refuelling capability in the sim just
now. It takes about 4 gallons use before you see the fuel guages begin
to drop since there's 28 gal per tank but the guages go to 26.
DG heading bug initializes to a random setting.
Activating heading hold doesn't touch the DG heading bug any more.
Max autopilot decent rate is now -1000.
Basically I've rewritten the prop model along similar lines to how
Jon has done his - using published efficiency and coefficient of
power data. It works *much* better - try pulling the throttle back
to idle and putting the plane into a dive before and after updating
and you'll see what I mean. It doesn't require a fudge factor either
:-)
good as we can get" until we find a data source with actual VOR magnetic
offsets. We can use VOR offsets from some fixed date, but not all VOR's
were installed on the same day so no matter what date we pick we will be off on most of them.
restoreInitialState methods to FGGlobals, as well as the two-stage
commit described above for loading saved files. fgInit now takes a
snapshot of the initial state before handing off to the main loop, and
the GUI reInit function restores that state explicitly before calling
fgReInit.
The FlightGear patches also modify fg_props.hxx to add optional
useDefault arguments to all of the fgTie functions -- that lets you
choose whether you want to pick up any default value in the property
tree when you tie the property (the default is true).
FGOptions is history, and the modules are (starting) to use the property
manager directly. Let me know if I left any files out.
Inevitably, there will be some problems with broken options, etc.,
that I haven't found in my tests, but I'll try to fix them quickly.
We also need to stress that the property names currently in use are
not stable -- we need to reorganize them a bit for clarity.
