utils/Modeller/Makefile.am src/FDM/YASim/Makefile.am:
Remove -lssg from the linker lines.
Do no longer build threedconvert. A very similar functionality
is available with osgvconv. But leave threedconvert in place
if somebody will need that ...
I found a small conspicuity in YASim. The destructor of the fdm was
never called, therefore a modification of the heli fdm (not in cvs) did
not work after reset (I tie some properties and untie them in the
destructor, but the destructor was not called and the tieing failed
after reset. I don't know if any other parts of YASim need their
destructors, at least it wastes memory.
Another small fix I have made to the turbulence.cpp. The code needed,
that (a-floor(a)) is >=0 and <1. This is analytical correct, but
numerical only for "small" values. In normal fg-operation a in this
function is always small, but with unrealistic parameters in the
aircraft config file it is not and then fg crashes (instead a crash of
the aircraft or cataputling it far away).
More realistic calculation of vortices at the blades and therefore
real airfoil parameters can be used now (not to be mixed up with the
vortex ring state which is still not simulated), ground effect is now
continuous e. g. at buildings, calculating of the rotor in more than 4
directions, better documentation of the airfoil parameters.
values that were angles between the aircraft's orientation and the
global velocity vector, not the airflow velocity. So the HUD velocity
vector was wrong when the wind was non-zero. Fix that.
generates a data file of aerodynamic lift and drag (and L/D) against
AoA at a specified speed and altitude through a full circle. Wrote it
to track down the YF-23 superthrust issue, but it wasn't any help.
All the forces look fine.
state. The only really obvious problem was a giant negative engine
RPM, which happened because of a lack of clamping in the engine code
combined with the YF-23's ability to actually reach speeds near the
engines _vMax value. It's not clear to me that this will fix the
superthrust issue at high AoA's, but it's an obvious bug nonetheless.
+ The wing compilation step was accidentally omitting regions that lie
between the tips and the first/last control object. That's a real
problem for wings that contain no controls, and a significant issue
for those that contain only a few. I'm stunned that this went
undetected for so long.
+ The Surface::flapLift() function was oddly returning 1.0 Newtons as
a minimum, instead of zero.
bunch of memory leaks that had accumulated over the years. FlightGear
doesn't currently bother to destroy and recreate a YASim context, but
at least it can do so now without worry.
groundcache addition -- the ground callback doesn't do anything at
solution time, so the ground plane was unset. Valgrind was whining
about this; it's not clear that it was actually causing a problem.
and in the calculation of the launchbar angle (by Vivian).
It also calculates the holdback angle, and sets a Boolean value which
can be used to initiate the release of the catapult strop submodel at
the appropriate moment (new code by Vivian).
control to piston engines that allows external scripts to control the
turbo/supercharger boost programatically by setting this axis to
values in the range [0:1]. It also adds a "turbo-lag" attribute (a
time in seconds) to engines implementing turbocharger spooling delays.
This isn't terribly well tested, but doesn't seem to have broken
anything.
propeller pitch stops for constant speed propellers. The default
values are the same as the previous hard-coded values. The new
attributes, "fine-stop" and "coarse-stop", are documented in the base
package, Docs/README.yasim.
This patch makes use of the vectors now available in simgear with that past
patch. And using that it simplyfies the carrier code somehow.
- Small additional factory's to the quaternion code are done in the simgear
part. Also more explicit unit names in the factory functions.
- The flightgear part makes use of them and simplyfies some computations
especially in the carrier code.
- The data part fixes the coordinate frames I used for the park positions in
the carrier to match the usual ones. I believed that I had done so, but it
was definitly different. Also there are more parking positions avaliable now.
are sharp, as intended. These were are never seen in practice; I
found the problem while looking at 360 degree lift curve graphs
looking for discontinuities.
"jitter" when the aircraft was stopped. This is a fundamental
characteristic of the gear model, and can't be fixed without major
surgery (and not a small amount of blinding insight). But we can at
least clamp it so the value can't change unless the wheel is moving
with a nontrivial velocity (5cm/sec in this case).
Attached is a patch to add oil temperature to the YASim piston engine
model. This brings to life one of the pa28-161's otherwise 'dead'
guages. It's a pretty simple 'model' based on temperatures and warmup
times I've observed in the labs on auto engines and run through my
dodgy-memory filter. It does the job of populating the guage with
something plausible though.
it for the B-29). The gear model itself has supported this always,
but there was no interface from the XML file. Should be backwards
compatible. I don't think I broke anything...
I believe I have found the agl hud problems as well as the 'hole' in the
carrier's deck. I spent half the day to reproduce that problem, it did not
occure when you start on the carrier not does it occure with JSBSim and my
really often used testaircraft. So I really need to improove my helicopter
flying qualities.
I was under the impression that *all* FDM's call
FGInterface::updateGeo*Position(..)
so set the new position in the FDM interface. Therefore I had added at the
some code that updates the scenery elevation below the aircraft to *those*
functions.
Ok, not all FDM's do so :/
The attached patch factors out a function computing the scenery altitude at
the current FDM's position. This function is also used in those FDM's which
need to update this value themselves.
Also this patch restores the nearplane setting and uses the current views
altitude instead of the current aircrafts. I think that this should further
be changed to the eypoint's agl in the future.
The agl is again ok in YASim's hud.
I have traced that reset on carrier problem down to several problems. One of
them is the fact that on reset the carrier is updated while the aircraft is
not. That made the aircraft drop down an elevator sometimes. Depending on the
passed realtime while loading some parts of the scenery.
