so they can instantly adjust to the changed environment.
(Not fully working yet, since some environment settings, like environemnt
pressure/temperature, still changes slowly after a sim reset - instead of
immediately jumping to the new setting. Also, METAR sometimes arrives too
late...).
- initialize uninitialized properties
- use prefix instead of postfix increments
- reduce visibility of variables
- use empty() instead of size() == 0 for vector and string
- pass string by reference, not by value
This is the initial commit for a reworked environment controller.
The main intention is to decouple the individual modules like
metar fetch, metar properties, environment interpolation etc.
to make it easier for other weather module developers to modify
environment settings.
As a side effect, the dialogs for weather-scenario, weather-conditions,
clouds and precipitations have been merged into a single dialog
This fix (re)enables the setting of temperature and
dewpoint from the weather-conditions dialog and other
sources for various altitude layers. These temperatures
are reduced to the corresponding sea level temperatures
according to ICAO standard atmosphere which is the inverse
function of the calculation of temperature at altitude based
on sea-level-temperature.
Note: this only works for the troposphere.
8:: AWOS is available at AWOS locations. (Previously only ATIS was
implemented.)
9:: ATIS phraseology now more nearly conforms to international
standard METAR pattern, and therefore to usual FAA practice.(*)
Items marked with a (*) are fully implemented in the /text/ of the
ATIS message, but the voiced version of the message is degraded by
limitations of the FGFS built-in text-to-speech system.
10:: ATIS now reports sky condition.(*)
11:: ATIS now reports multiple layers of clouds, not just the lowest
layer.(*)
12:: ATIS now takes field elevation into account when calculating
sky condition and ceiling.
13:: ATIS now reports dewpoint.(*)
14:: ATIS now can handle negative quantities (temperature and dewpoint).(*)
15:: ATIS can now report report fractional-mile visibility.(*)
16:: ATIS now uses magnetic (not true) wind directions, as it should.
17:: ATIS generates correct runway number and suffix (nine right,
one one left).
18:: ATIS can be received on nav frequencies, not just comm.
19:: Nothing bad happens if the same ATIS is tuned up on more than
one receiver.
20:: ATIS can be updated at times other than at the top of the hour.
21:: ATIS listens for an "attention" signal, and responds to changes
in the weather by issuing a new ATIS message (somewhat like a
"special observation").
22:: ATIS volume now responds to radio volume setting.
23:: Area-related services (i.e. approach radar) are handled
more-nearly consistently with radio-frequency related services.
24:: ATIS sequence-letter generation has been fixed.
25:: ATIS messages are now in the property tree, so they can be read
e.g. via the http interface.
Conflicts:
src/Environment/environment.cxx
src/Environment/environment.hxx
John Denker's atmosphere changes. Original commit message:
Two-parameter physics-based model of atmosphere up to 262,467 ft i.e.
the top of the mesosphere. Correctly exhibits the HALT phenomenon.
* Use "const string&" rather than "string" in function calls when appropriate.
* Use "const Point3D&" instead of "Pint3D" in function calls when appropriate.
* Improved course calculation in calc_gc_course_dist()
* Safer thread handling code.
Vassilii Khachaturov:
Dont use "const Point3D&" for return types unless you're absolutely sure.
Erik Hofman:
* Use SGD_(2)PI(_[24]) as defined in simgear/constants.h rather than
calculating it by hand every time.
This is another update for the cloud code, a lot of lines but this time I have started to add the doxygen doc.
Misc
====
- corrected a bug when RTT is not available, the current rendering context was
altered
- if RTT is not available then 3d clouds are not drawn at all
- impostors lighting is now recomputed when the sun changes position
- distant objects are no more seen in front of clouds
- blending of distant clouds is a bit better now
- litle optimization of code (uses a less cpu time)
- use layer wind speed and direction (no more hardcoded wind)
- fov is no more hardcoded
Changes
=======
- clouds (cu only) are dissipating/reforming (experimental)
- compute a turbulence factor that depends on surrounding clouds and type of
clouds (experimental)
- clouds shapes are defined in cloudlayers.xml
- type of clouds present in a layer is also defined in cloudlayers.xml
- cloud layers are generated from metar and other misc. data (in progress)
- added a rain effect around the viewer (enabled in the rendering dialog and
when the metar property says so)
- added a lightning effect (enabled in the rendering dialog) : cb clouds spawn
new lightnings
- added a dialog to select from different weather source : metar/property,
a 'fair weather' environment and a 'thunderstorm' environment.
Upon further review, I was very misguided, and unfortunately no one slapped
my hand at the time.
Factoring in the environment manager's interpolation scheme, it makes complete
sense to specify the sea level temperature at each boundary and aloft layer.
In fact, this is the only way that allows the temperature interpolation to
make sense, especially around the boundary layer. This is confusing stuff,
but it now works perfectly. :-)
Square the normalized direction acceleration for the y and z axes, so
that turbulence predominantly affects pitch.
Bind to the /environment/turbulence/magnitude-norm and
/environment/turbulence/rate-hz properties in FlightGear.
between temperature at altitude vs. temperature at sea level. The dialog
box asked for temperature at altitude which makes sense, but all the
internal crunching expected temperature at sea level. However, it makes no
logical sense to specify the sea level temperature for different layers so
I changed the internal processing to work with temperature at altitude and
then derive an approximate sea level temperature at the end.
If you know the ground temperature, you can just enter this temperature
for the first boundary layer and the system should do the right thing.
etc.
Improved the weather system to interpolate between different
elevations and deal with boundary-layer conditions. The configuration
properties are now different (see $FG_ROOT/preferences.xml).
