I have done some cleanup where I moved some values out of classes where they
do not belong and such stuff.
Also the fols offsets are now named in the carrier xml file with a more
verbose name (flols-pos/offset-*) than before (only offset-*).
There is a little preparation for definitions of parking positions on the
carrier which should later be used for starting flightgear directly on the
carrier.
I just heard from John Wojnaroski that you and he are going to work on getting
a flightgear demo machine up for the linux expo thursday and Friday. John
indicated that he would very much like to get a CVS version with the new
traffic code up and running before the expo.
This is a sub-system which can be added to any carrier.
These files add a functioning Fresnel Lens Optical Landing System (FLOLS).
The orange/red 'source' lights are illuminated according to the position of
the pilot's eye above/below the 3.5 deg glide slope. The apparent position
of the source light relative to the fixed green datum lights allow the pilot
to 'fly the meatball'. The green 'cut' lights flash when the pilot's eye is
below the coverage of the lowest (red) source light.
TODO - add rules for the operation of the wave-off lights.
Okay, here's the latest update to the tarffic manager/AI Manager. AITraffic
can now fly multiple routes and be initialized while sitting statically at
airports.
As a result of recent requests, I've implemented the ability to switch off
aerodynamic stabilisation:
This has to be added to the submodel.xml files:
<aero-stabilised>false</aero-stabilised>
When false the submodel retains the pitch given at instantiation.
It defaults to true.
The calculation of submodel mass from weight has been moved from AIBallistic
to Submodel so that it is calculated only once, rather than on every
iteration as a present. The parameter <contents> has been added, primarily
so that droptanks will have the proper mass. It is the path to an
appropriate property containing a weight in lbs.
Care has to be taken with the use of <contents> because after a reset there
appears to be a delay in submodel instantiation (dt not properly reset???)
and the weight property is not always picked up before it is set to zero in
the key bindings. Slightly hard to explain. It works fine if FGFS has not
been reset though. There is a partial solution which involves the rejigging
of the fuel and gui nasal scripts, but there is still the visible delay in
instantiation to be resolved. I've nearly done the nasal fixes, which will
form part of an update to the Hunter only. I'll probably complete those
later today.
The value of rho (air density) varies with height. (Including the upper
stratosphere, ust in case someone wants to model ICBMs.) The standard
atmosphere is used (based on a sea-level temperature of 15 deg C.).
Erik Hofman:
I moved this code over the AIBase::update() so all AIModels can make
use of rho, temperature, pressure, etc.
I have added <Cd> and <weight> to the input parameters in the submodels.xml
script. Raw data may be used, thus avoiding the need to guestimate <eda>.
Eda remains, but should now be used to enter the proper cross-sectional
area.
I had to reverse a number of signs to get it right. I took the opportunity
to add roll to the submodel so that droptanks will come off with the right
orientation. I have neither added the rotational speed to the submodel, nor
yaw, so if you release droptanks with significant roll rate or yaw angle on
the aircraft the submodel will not be quite right. Straight and level, or
nearly so, is fine.
I've added another parameter to the submodel - wind.
It's activated by the entry <wind>true</wind> in the ../submodel.xml file.
If true, the submodel is affected by the local wind, otherwise not. The
parameter defaults to false. This is useful for exhausts and smoke, and
possibly all objects.
Attached are the modified files to add buoyancy as a parameter for a
ballistic object. It may be set by adding
<buoyancy>x</buoyancy> to the submodel .xml file, where x is the appropriate
value (ft per sec2):
32 neutral buoyancy - contrails
>32 positive buoyancy - exhaust plumes
(0 non-op - default value)
If <buoyancy>x</buoyancy> is not used, then there is no effect on the
current ballistic model
Silly me. I was starting the timer at zero, so the first tracer didn't fly
until 0.25 seconds after pulling the trigger. Now the timer starts at the
same value as "delay", so the first round comes out immediately.
Also, I've added an optional configuration attribute that allows you to change
the ballistics of the submodel. This allows parachutes, or anything else
that has ballistics different from a bullet. The attribute is called "eda",
which is the equivalent drag area. Default value is 0.007, which gives the
same ballistics as the current tracers. Increasing this value gives more
drag. A value of 2.0 looks good for a parachute.
math stuff
########################################################################
The deceleration of the ballictic object is now given by:
[ (rho) (Cd) ] / [ (1/2) (m) ] * A * (V * V)
where rho is sea-level air density, and Cd and m are fixed, bullet-like
values. So the calculation is:
0.0116918 * A * (V * V)
The value "A" is what I'm calling the "eda" (equivalent drag area).
########################################################################
A parachute model will have to be built so that the parachutist's feet
are in the forward x-direction.
Here is the submodel.xml config I use for "parachutes":
<submodel>
<name>flares</name>
<model>Models/Geometry/flare.ac</model>
<trigger>systems/submodels/submodel[0]/trigger</trigger>
<speed>0.0</speed>
<repeat>true</repeat>
<delay>0.85</delay>
<count>4</count>
<x-offset>0.0</x-offset>
<y-offset>0.0</y-offset>
<z-offset>-4.0</z-offset>
<yaw-offset>0.0</yaw-offset>
<pitch-offset>0.0</pitch-offset>
<eda>2.0</eda>
</submodel>
Here's some additions to AI that allow refueling from an AI tanker (the actual
onload of fuel must be handled by the user's FDM of course, this just lets
the FDM know that the user is in position to refuel).
I've added a new class of AIAircraft called "tanker". It uses the same
performance struct as a jet transport. An AI tanker is just like an AI jet
transport, except it uses the already-existing radar data to control the
boolean property systems/refuel/contact. The code change was minimal.
An AI tanker can be created like this:
<entry>
<callsign>Esso 1</callsign>
<type>aircraft</type>
<class>tanker</class>
<model>Aircraft/737/Models/boeing733.xml</model>
<latitude>37.61633</latitude>
<longitude>-122.38334</longitude>
<altitude>3000</altitude>
<heading>020</heading>
<speed>280</speed>
<roll>-15</roll>
</entry>
This puts a tanker over KSFO at 3000 feet, in a left-hand orbit. When the
user gets within refueling range (contact position) then the property
systems/refuel/contact will be true. Otherwise it is false.
The dimensions of the refueling envelope are pretty rough right now, but still
usable. The user must be behind the tanker (ie. radar y_offset > 0). The
user must be at or below the tanker's altitude (ie. radar elevation > 0).
The user's lat/lon must be within 250 feet of the tanker's lat/lon (ie. radar
range_ft < 250). This last requirement is loose because the radar data is
only updated every 100 ms, which is accurate enough for radar use, but
which is sloppy for air refueling. This could be tightened up by increasing
the radar update rate to once every sim cycle.
I'm going to add a light to the T-38 instrument panel that will monitor the
property systems/refuel/contact. This will make it easier to explore the
boundaries of the refueling envelope.
Here's some new AI stuff.
1) AI objects must now be defined in a scenario file, not in preferences.xml
or a *-set file. (Of course this doesn't prevent objects from being created
dynamically, as with Durk's traffic manager).
2) A new demo_scenario file is attached. It creates 3 aircraft, a sailboat,
and a thunderstorm.
3) Objects without flightplans live forever.
4) FGAIShip::ProcessFlightplan() is not yet implemented.
5) preferences.xml should now define only <enabled> and <scenario>
1. Removed aircraft roll on ground.
2. Decreased descent pitch angle.
3. Updated flightplans to include <on-ground>
4. Fixed property indexing, so all AI aircraft have their own property branch
The default value of <on-ground> is false, so you only need to specify it when
on the ground. For takeoff you need to specify <on-ground>true</on-ground>
for the first waypoint, and for the acceleration waypoint. For landing you
need to specify it for the touchdown point and any taxi points.
One problem. WARNING **** There is a bug in the way the property system
works, which causes a segfault, but I don't know if the problem is in the
property code, or in how I'm using it. After an AI object terminates, if you
access the property tree through the property browser the sim will segfault.
First, preferences.xml will define the scenario filename.
For now, the other way of defining ai objects still works, so the sailboat
stays in preferences.xml. Later, I'll move the sailboat into the demo
scenario. If no scenario filename is given, then no scenario will be
processed.
I changed the demo scenario to create two 737's, one takes off on runway 01L,
and the other takes off on runway 01R. This will make a good demo for the ai
system. One problem, if you takeoff on 28L/R right away, you might run into
the taking-off 737's, or be scared.
Here's the newest AI stuff.
The AIManager at init() creates a new scenario. Right now the
default_scenario is hard coded in, but eventually the AIManager should get
the scenario filename from preferences.xml.
The scenario defines which AI objects will be created. Right now it only
creates AIAircraft, but this is easily extended. The scenario also defines
which flightplan will be assigned to the airplane. Scenario config files go
in data/Data/AI.
The Airplane gets a pointer to a FlightPlan object. Each airplane should get
its own flightplan object, even if two airplanes have the same flight plan.
This is because the flightplan maintains the iterator pointing to the
current waypoint, and two airplanes might be at different locations (for
instance if they were created at different times). The flight plan files go
in data/Data/AI/FlightPlans.
When the airplane gets to the waypoint named "END" it vanishes. The
AIAircraft destructor deletes its flight plan (if it has one).
The last waypoint is a place holder only. I called mine
<WPT><NAME>"EOF"</NAME></WPT>.
I added some things to the AI stuff to improve the AIThermal processing.
Before, all the thermals were processed in order, and the last one overwrote
the prior one. Now, only the data from the nearest thermal is kept. This
way a tile can be populated with many thermals, and (as long as they have the
same diameter) the one nearest the airplane correctly takes effect. This
will make us ready for the next step, "auto-thermaling", where FlightGear's
tile manager can cover a tile with thermals, and set the thermal strength
based on land-use type.
I moved the enumerated object_type to the base class. When an AI object is
created it now sets the _otype variable in the base class. This lets the AI
manager find out what kind of AI object it is dealing with, using the base
pointer. I also added a function isa() to the base class, so the manager can
process objects differently based on their type.
The AI manager now sends AIThermal processing to a different function, where
only the data from the nearest thermal is kept. After the manager processes
all the AI objects, then the results from the nearest thermal are applied to
wind-from-down.
Here's a new batch of AI code which includes a working radar instrument.
I put the radar calculations into the existing AIAircraft class. It was
easier that way, and it can always be migrated out later if we have to.
Every tenth sim cycle the AIManager makes a copy of the current user state
information. When the AIAircraft updates it uses this information to
calculate the radar numbers. It calculates:
1) bearing from user to target
2) range to target in nautical miles
3) "horizontal offset" to target. This is the angle from the nose to the
target, in degrees, from -180 to 180. This will be useful later for a HUD.
4) elevation, in degrees (vertical angle from user's position to target
position)
5) vertical offset, in degrees (this is elevation corrected for user's pitch)
6) rdot (range rate in knots, note: not working yet, so I commented it out)
and three items used by the radar instrument to place the "blip"
7) y_shift, in nautical miles
8) x_shift, in nautical miles
9) rotation, in degrees
The radar instrument uses the above three items, and applies a scale factor to
the x-shift and y-shift in order to match the instrument's scale. Changing
the display scale can be done entirely in the XML code for the instrument.
Right now it's set up only to display a 40 mile scale.
The radar is an AWACS view, which is not very realistic, but it is useful and
demonstrates the technology. With just a little more work I can get a HUD
marker. All I need to do there is make a bank angle adjustment to the
current values.
I went through the AI code to put the "bank" node back into the config file,
so the models can fly circles. While I was in there I made some other
changes.
*) Moved the initialization of roll, tgt-roll, pitch ... etc, from init()
into the constructor, so it wouldn't over-write the config settings.
*) Changed the altitude getter to remove the meters-to-feet conversion. The
altitude is kept internally in feet. Only the scenery code needs meters.
*) Added "bank" item for config file (for type=aircraft). Left bank is
negative.
*) Added "rudder" item for config file (for type=ship). Left rudder is
negative. Internally this is stored in the "roll" variable, but the ship
model doesn't roll. It uses the "roll" variable for turning though.
The following puts a tanker at 3000 feet, 6 nm northwest of KSFO. On takeoff,
the tanker is visible over the hanger building at one-o'clock.
<entry>
<type>aircraft</type>
<class>jet_transport</class>
<path>Aircraft/737/Models/boeing733.xml</path>
<speed-KTAS type="double">320.0</speed-KTAS>
<altitude-ft type="double">3000.0</altitude-ft>
<longitude type="double">-122.455</longitude>
<latitude type="double">37.69667</latitude>
<heading type="double">200.0</heading>
<bank type="double">-15.0</bank>
</entry>
