Here's a new FGSimTurbine module. Changes are:
1. Adds starting and stopping functionality
2. Calculate() now calls other functions, based on the engine's state, which gives more readable code.
Until now turbine engines were always running as long as fuel was available. With this new module the engine defaults to OFF. To start with the engine running, the variable FGEngine::Running must be set to true at sim startup. In FlightGear this is done with --prop:/engines/engine[n]/running=true.
To start the engine (on the ground), first set the starter to ON, i.e. FGEngine::Starter is set to true. In FlightGear this is done by toggling /controls/engines/engine[n]/starter to TRUE. Note that the current FlightGear key binding will not work, as it causes the starter to quit when the key is released. A new key binding is needed, without the mod-up.
When N2 reaches 15% or greater, place the fuel cutoff control to FALSE. This is FGEngine::Cutoff. In FlightGear this is done with /controls/engines/engine[n]/cutoff set to FALSE. The engine will then accelerate to idle. Upon reaching idle, the starter is automatically turned off, and the engine is running. There is presently no FlightGear key binding for the fuel cutoff switch.
To shut off the engine, place the fuel cutoff control to TRUE.
If you shut down the engine in flight it will windmill. To airstart you will need at least 15% N2, just as with a ground start. When you have enough N2, place the cutoff control to FALSE and the engine will restart. Note that if you can't get enough N2 by speeding up, you can get it by using the starter.
The reverser still works, and is controlled in FlightGear with /controls/engines/engine[n]/reverser. With the reverser control on (TRUE), the engine will produce negative thrust in proportion to throttle position, i.e. to get more reverse
thrust, increase throttle.
Square the normalized direction acceleration for the y and z axes, so
that turbulence predominantly affects pitch.
Bind to the /environment/turbulence/magnitude-norm and
/environment/turbulence/rate-hz properties in FlightGear.
The general idea is to help clean up some aspects of the FDM init and be
able to provide startup conditions in a less ambiguous manner.
Previously, things like positions, orientations, and velocites were set on
"the bus". These had to be read by the FDMs which then were supposed to
initialized themselves to those values and turn write around and start
modifying those values. It was messy and cumbersome.
Now, all the initial fdm conditions are written to a sub-[property-]tree
under /sim/presets/
The values in /sim/presets/ always stay set to what the user has specified.
The user can change these at his/her liesure, and then request a "reset"
which will reset to the new conditions. I don't even want to say how this
worked before. :-)
Now, an script, or gui interface can stage a set of initial conditions while
the sim is running (without disrupting it), and then call "reset" to commit
the change.
People who should worry about all this are FDM writters, and a small few
others who care about over all program structure and flow.
This is a new improved patch for the previous tile manager fixes.
Rather than building dependencies between FGlocation or the viewer or fdm with
tilemgr what I ended up doing was linking the pieces together in the Mainloop
in main.cxx. You'll see what I mean...it's been commented fairly well. More
than likely we should move that chunk somewhere...just not sure where yet.
The changes seem clean now. As I get more ideas there could be some further
improvement in organizing the update in tilemgr. You'll note that I left an
override in there for the tilemgr::update() function to preserve earlier
functionality if someone needs it (e.g. usage independent of an fdm or
viewer), not to mention there are a few places in flightgear that call it
directly that have not been changed to the new interface (and may not need to be).
The code has been optimized to avoid duplicate traversals and seems to run
generally quite well. Note that there can be a short delay reloading tiles
that have been dropped from static views. We could call the tile scheduler on
a view switch, but it's not a big deal and at the moment I'd like to get this
in so people can try it and comment on it as it is.
Everything has been resycned with CVS tonight and I've included the
description submitted earlier (below).
Best,
Jim
Changes synced with CVS approx 20:30EDT 2002-05-09 (after this evenings updates).
Files:
http://www.spiderbark.com/fgfs/viewer-update-20020516.tar.gz
or
http://www.spiderbark.com/fgfs/viewer-update-20020516.diffs.gz
Description:
In a nutshell, these patches begin to take what was one value for ground
elevation and calculate ground elevation values seperately for the FDM and the
viewer (eye position). Several outstanding view related bugs have been fixed.
With the introduction of the new viewer code a lot of that Flight Gear code
broke related to use of a global variable called "scenery.cur_elev".
Therefore the ground_elevation and other associated items (like the current
tile bucket) is maintained per FDM instance and per View. Each of these has a
"point" or location that can be identified. See changes to FGLocation class
and main.cxx.
Most of the problems related to the new viewer in terms of sky, ground and
runway lights, and tower views are fixed.
There are four minor problems remaining. 1) The sun/moon spins when you pan
the "lookat" tower view only (view #3). 2) Under stress (esp. magic carpet
full speed with max visibility), there is a memory leak in the tile caching
that was not introduced with these changes. 3) I have not tested these
changes or made corrections to the ADA or External FDM interfaces. 4) The
change view function doesn't call the time/light update (not a problem unless
a tower is very far away).
Details:
FDM/flight.cxx, flight.hxx - FGInterface ties to FGAircraftModel so that it's
location data can be accessed for runway (ground elevation under aircraft)
elevation.
FDM/larsim.cxx, larcsim.hxx - gets runway elevation from FGInterface now.
Commented out function that is causing a namespace conflict, hasn't been
called with recent code anyway.
FDM/JSBSim/JSBSim.cxx, YASim/YASim.cxx - gets runway elevation from
FGInterface now.
Scenery/newcache.cxx, newcache.hxx - changed caching scheme to time based
(oldest tiles discard).
Scenery/tileentry.cxx, tileentry.hxx - added place to record time, changed
rendering to reference viewer altitude in order to fix a problem with ground
and runway lights.
Scenery/tilemgr.cxx, tilemgr.hxx - Modified update() to accept values for
multiple locations. Refresh function added in order to periodically make
the tiles current for a non-moving view (like a tower).
Main/fg_init.cxx - register event for making tiles current in a non-moving
view (like a tower).
Main/location.hxx - added support for current ground elevation data.
Main/main.cxx - added second tilemgr call for fdm, fixed places where viewer
position data was required for correct sky rendering.
Main/options.cxx - fixed segfault reported by Curtis when using --view-offset
command line parameter.
Main/viewer.cxx, viewer.hxx - removed fudging of view position. Fixed numerous
bugs that were causing eye and target values to get mixed up.
set_Density; since JSBSim doesn't override the get_* methods from
FGInterface as well, the wrong values are always set anyway.
Take the static temperature, static pressure, and density values from
an external source if requested by the
/environment/params/control-fdm-atmosphere property. This isn't
working properly yet for JSBSim because of interactions with the
trimming routine.
- changed FGSubsystem::update(int) to
FGSubsystem::update(delta_time_sec); the argument is now delta time
in seconds rather than milliseconds
- added FGSubsystem::suspend(), FGSubsystem::suspend(bool),
FGSubsystem::resume(), and FGSubsystem::is_suspended(), all with
default implementations; is_suspended takes account of the master
freeze as well as the subsystem's individual suspended state
- the FDMs now use the delta time argument the same as the rest of
FlightGear; formerly, main.cxx made a special case and passed a
multiloop argument
- FDMs now calculate multiloop internally instead of relying on
main.cxx
There are probably some problems -- I've done basic testing with the
major FDMs and subsystems, but we'll probably need a few weeks to
sniff out bugs.
