- Removed some old cruft.
- Removed some support for older versions of automake which technically was
correct, but caused the newer automakes to squawk warnings during an
initial sanity check (which isn't done very intelligently.)
NOTE: this fix is technically not correct for older version of automake.
These older version use the variable "INCLUDES" internally and could have
them already set to an important value. That is why we were appending
our values to them. However, newer versions of automake don't set this
value themselves so it is an error to append to a non-existant variable.
We seem to "get away" with overwriting the value on older versions of
automake, but if you have problems, consider upgrading to at least
automake-1.5.
I have finished working the bugs out of my "Enhanced" version of the Magic
Carpet FDM. The UFO FDM works the same as the Magic Carpet with the
following exceptions:
The aircraft's pitch is determined by the Elevator setting (with a pitch
rate of 45 degrees per second).
Climb is forward velocity * sin(pitch)
Speed is forward velocity * soc(pitch)
Roll is tied to the aileron (again, with a roll rate of 45 degrees per
second)
Turn rate is sin(roll) * 45 degrees.
Yes, this does mean that turning is quite a bit more sluggish than
climbing.
If you are wondering why a UFO FDM, it is because it's best that I not
replace the existing magic carpet and this FDM does behave like a UFO (it
hovers, can spin and pitch while hovering, and does not obey the laws of
physics ;)
- automake-1.4 sets default values for INCLUDES which we can't
overwrite.
- automake-1.5 renames this to DEFAULT_INCLUDES and leaves INCLUDES
open for the developer to use.
Thus for automake-1.4 we are forced to 'append' to INCLUDES and in
automake-1.5 we can just set the value to whatever we like.
Unfortunately, the behaviors of the two versions are mutually
incompatible.
The solution I am committing now works for both versions but
automake-1.5 generates a lot of spurious warning messages that are
annoying, but not fatal.
Dynamics (Sim)ulator. Basically, this is a rough, first cut of a "different
take" on FDM design. It's intended to be very simple to use,
producing reasonable results for aircraft of all sorts and sizes,
while maintaining simulation plausibility even in odd flight
conditions like spins and aerobatics. It's at the point now where one
can actually fly the planes around.
one I sent yesterday. I have re-zipped all four files so you can
neglect the last lot but only io360.cxx has changed if you've
already committed. It's untested since I can't start the engine until
John has committed his update with separate properties. Should
work fine though.
LaRCsim c172 on-ground and in-air starts, reset: all work
UIUC Cessna172 on-ground and in-air starts work as expected, reset
results in an aircraft that is upside down but does not crash FG. I
don't know what it was like before, so it may well be no change.
JSBSim c172 and X15 in-air starts work fine, resets now work (and are
trimmed), on-ground starts do not -- the c172 ends up on its back. I
suspect this is no worse than before.
I did not test:
Balloon (the weather code returns nan's for the atmosphere data --this
is in the weather module and apparently is a linux only bug)
ADA (don't know how)
MagicCarpet (needs work yet)
External (don't know how)
known to be broken:
LaRCsim c172 on-ground starts with a negative terrain altitude (this
happens at KPAO when the scenery is not present). The FDM inits to
about 50 feet AGL and the model falls to the ground. It does stay
upright, however, and seems to be fine once it settles out, FWIW.
To do:
--implement set_Model on the bus
--bring Christian's weather data into JSBSim
-- add default method to bus for updating things like the sin and cos of
latitude (for Balloon, MagicCarpet)
-- lots of cleanup
The files:
src/FDM/flight.cxx
src/FDM/flight.hxx
-- all data members now declared protected instead of private.
-- eliminated all but a small set of 'setters', no change to getters.
-- that small set is declared virtual, the default implementation
provided preserves the old behavior
-- all of the vector data members are now initialized.
-- added busdump() method -- FG_LOG's all the bus data when called,
useful for diagnostics.
src/FDM/ADA.cxx
-- bus data members now directly assigned to
src/FDM/Balloon.cxx
-- bus data members now directly assigned to
-- changed V_equiv_kts to V_calibrated_kts
src/FDM/JSBSim.cxx
src/FDM/JSBSim.hxx
-- bus data members now directly assigned to
-- implemented the FGInterface virtual setters with JSBSim specific
logic
-- changed the static FDMExec to a dynamic fdmex (needed so that the
JSBSim object can be deleted when a model change is called for)
-- implemented constructor and destructor, moved some of the logic
formerly in init() to constructor
-- added logic to bring up FGEngInterface objects and set the RPM and
throttle values.
src/FDM/LaRCsim.cxx
src/FDM/LaRCsim.hxx
-- bus data members now directly assigned to
-- implemented the FGInterface virtual setters with LaRCsim specific
logic, uses LaRCsimIC
-- implemented constructor and destructor, moved some of the logic
formerly in init() to constructor
-- moved default inertias to here from fg_init.cxx
-- eliminated the climb rate calculation. The equivalent, climb_rate =
-1*vdown, is now in copy_from_LaRCsim().
src/FDM/LaRCsimIC.cxx
src/FDM/LaRCsimIC.hxx
-- similar to FGInitialCondition, this class has all the logic needed to
turn data like Vc and Mach into the more fundamental quantities LaRCsim
needs to initialize.
-- put it in src/FDM since it is a class
src/FDM/MagicCarpet.cxx
-- bus data members now directly assigned to
src/FDM/Makefile.am
-- adds LaRCsimIC.hxx and cxx
src/FDM/JSBSim/FGAtmosphere.h
src/FDM/JSBSim/FGDefs.h
src/FDM/JSBSim/FGInitialCondition.cpp
src/FDM/JSBSim/FGInitialCondition.h
src/FDM/JSBSim/JSBSim.cpp
-- changes to accomodate the new bus
src/FDM/LaRCsim/atmos_62.h
src/FDM/LaRCsim/ls_geodesy.h
-- surrounded prototypes with #ifdef __cplusplus ... #endif , functions
here are needed in LaRCsimIC
src/FDM/LaRCsim/c172_main.c
src/FDM/LaRCsim/cherokee_aero.c
src/FDM/LaRCsim/ls_aux.c
src/FDM/LaRCsim/ls_constants.h
src/FDM/LaRCsim/ls_geodesy.c
src/FDM/LaRCsim/ls_geodesy.h
src/FDM/LaRCsim/ls_step.c
src/FDM/UIUCModel/uiuc_betaprobe.cpp
-- changed PI to LS_PI, eliminates preprocessor naming conflict with
weather module
src/FDM/LaRCsim/ls_interface.c
src/FDM/LaRCsim/ls_interface.h
-- added function ls_set_model_dt()
src/Main/bfi.cxx
-- eliminated calls that set the NED speeds to body components. They
are no longer needed and confuse the new bus.
src/Main/fg_init.cxx
-- eliminated calls that just brought the bus data up-to-date (e.g.
set_sin_cos_latitude). or set default values. The bus now handles the
defaults and updates itself when the setters are called (for LaRCsim and
JSBSim). A default method for doing this needs to be added to the bus.
-- added fgVelocityInit() to set the speed the user asked for. Both
JSBSim and LaRCsim can now be initialized using any of:
vc,mach, NED components, UVW components.
src/Main/main.cxx
--eliminated call to fgFDMSetGroundElevation, this data is now 'pulled'
onto the bus every update()
src/Main/options.cxx
src/Main/options.hxx
-- added enum to keep track of the speed requested by the user
-- eliminated calls to set NED velocity properties to body speeds, they
are no longer needed.
-- added options for the NED components.
src/Network/garmin.cxx
src/Network/nmea.cxx
--eliminated calls that just brought the bus data up-to-date (e.g.
set_sin_cos_latitude). The bus now updates itself when the setters are
called (for LaRCsim and JSBSim). A default method for doing this needs
to be added to the bus.
-- changed set_V_equiv_kts to set_V_calibrated_kts. set_V_equiv_kts no
longer exists ( get_V_equiv_kts still does, though)
src/WeatherCM/FGLocalWeatherDatabase.cpp
-- commented out the code to put the weather data on the bus, a
different scheme for this is needed.
ing features:
a) ADA Flight model - ADA.cxx, ADA.hxx, flight.hxx
b) Fighter a/c HUD - flight.hxx, hud.hxx, hud.cxx, cockpit.cxx, hud_ladr.c
xx, hud_card.cxx
c) 3-window display - options.hxx, options.cxx, viewer.cxx
d) Moving objects (ship) - main.cxx
e) Patches - main.cxx
ADA.cxx, ADA.hxx
--------------------------
Interface to the external ADA flight dynamics package.
flight.hxx
----------
Included prototypes for accepting additional data fron the External flight
model for fighter aircraft HUD
Hud.hxx
-------
Included prototypes for accepting additional data for fighter HUD from Exernal F
light model.
Defined FIGHTER_HUD pre-processor directive to enable compilation of fighter hud
code.
hud.cxx, cockpit.cxx, hud_ladr.cxx, hud_card.cxx
---------------------------------------
Included code to initialise additional reticles/text for fighter HUD which is co
nditionally
compiled if FIGHTER_HUD is defined.
options.hxx
-----------
Added window_offset, and function to retrieve its value for 3 windows
options.cxx
-----------
Changed few options to suit ADA/CEF projection system/screens and checks for win
dow offset.
views.cxx
---------
Added code to retrieve view offset for window.
Main.cxx
--------
Added code to load and move an aircraft carrier.
Patch to enable clouds from command line until Curtis fixes it. By default cloud
s are disabled.
