speedups to uiuc_menu.cpp.
(Note these were originally submitted before the cutoff date for new
features, but something was corrupted in the transfer so I granted a bit
of leeway in the schedule.)
- Removed some old cruft.
- Removed some support for older versions of automake which technically was
correct, but caused the newer automakes to squawk warnings during an
initial sanity check (which isn't done very intelligently.)
NOTE: this fix is technically not correct for older version of automake.
These older version use the variable "INCLUDES" internally and could have
them already set to an important value. That is why we were appending
our values to them. However, newer versions of automake don't set this
value themselves so it is an error to append to a non-existant variable.
We seem to "get away" with overwriting the value on older versions of
automake, but if you have problems, consider upgrading to at least
automake-1.5.
> I have attached some new additions to the UIUC code. Most of the
> changes allow for the addition of apparent mass. This is very
> useful with light aircraft and gliders.
ability to run a nonlinear model with flaps. The files ls_model.c and
uiuc_aero.c were changed since we had some functions with the same
name. The name changes doesn't affect the code, it just makes it a
little easier to read. There are changes in LaRCsim.cxx so UIUC
models have engine sound. Could you send me an email when you receive
this and/or when the changes make it to the CVS? Thanks.
Also I noticed you have some outdated files that are no longer used in
the UIUCModel directory. They are uiuc_initializemaps1.cpp,
uiuc_initializemaps2.cpp, uiuc_initializemaps3.cpp, and
uiuc_initializemaps4.cpp
Rob
different locations, and hitched it into FGGlobals. FGEnvironmentMgr
has taken over as the subsystem, while FGEnvironment is simple the
information that it returns. I've removed current_environment
completely -- everything now uses properties or goes through
FGGlobals. FGGlobals itself has a couple of useful methods:
const FGEnvironment * get_environment ();
const FGEnvironment * get_environment (double lat, double lon, double alt);
The first one returns the environment data for the plane's current
position, while the second returns the environment data for any
arbitrary location. Currently, they both return the same information,
but that will change soon.
properties have been renamed from wind-(north|east|down)-fps to
wind-from-(north|east|down)-fps, and the FDMs modified appropriately.
No other changes should be visible unless FG_OLD_WEATHER is defined.
- automake-1.4 sets default values for INCLUDES which we can't
overwrite.
- automake-1.5 renames this to DEFAULT_INCLUDES and leaves INCLUDES
open for the developer to use.
Thus for automake-1.4 we are forced to 'append' to INCLUDES and in
automake-1.5 we can just set the value to whatever we like.
Unfortunately, the behaviors of the two versions are mutually
incompatible.
The solution I am committing now works for both versions but
automake-1.5 generates a lot of spurious warning messages that are
annoying, but not fatal.
Here's an unusual patch for FlightGear -- I've created .cvsignore
files for every source directory, to make CVS output more informative.
This is especially nice when using cvs-examine from (X)Emacs to look
for changes.
hope, with earlier versions as well)
- support for the new LONG value type
- gear support for UIUC (updated for the newly renamed SG_* stuff;
otherwise identical to what I sent you before)
- fixed reported MSVC problem in src/FDM/flight.cxx
I have created a set of patches to provide configurable landing gear
for the UIUC models. The patches (including four new files) are
available at
http://megginson.com/private/fgfs/uiuc-20010309.tar.gz
A modified UIUC configuration file for the Twin Otter (DHC-6) is
available at
http://megginson.com/private/fgfs/aircraft.dat
It should be possible to configure appropriate gear for all of the
UIUC models now. As a bonus, the models also support braking, both
absolute and differential, as well as nose-wheel steering (all of
which are currently missing from the UIUC models) -- when you land,
you don't have to keep rolling off the end of the runway anymore, and
you don't have to bank to steer in a taxi.
My sample configuration file contains absolutely bizarre, wild
guesses, and many places that I didn't even bother to guess properly.
The only actual data I had was the wing-span of the DHC-6 (65ft),
which I used for positioning the wing tips. The wing-tips for this
model actually work now -- I hit the aileron hard while accelerating
for take-off, and the wingtip noticeably strikes the ground and
bounces up (quite dramatic in external view using the DHC-6 model from
Wolfram's site).
Details
-------
The UIUC models now support up to 16 gear points each where a gear
point is anything in the aircraft that can come in contact with the
ground, including the tail and wing-tips. I have added the following
new fields to the UIUC configuration files, where <index> is an
integer between 0 and 15, and <value> is a real number:
gear <index> Dx_gear <value> # x offset from CG [ft]
gear <index> Dy_gear <value> # y offset from CG [ft]
gear <index> Dz_gear <value> # z offset from CG [ft]
gear <index> cgear <value> # spring damping [lbs/ft/sec]
gear <index> kgear <value> # springiness [lbs/ft]
gear <index> muGear <value> # rolling coefficient
gear <index> strutLength <value> # gear travel [ft] (not yet used)
Most of these names were already pencilled into the UIUC documentation
(as TODO items), but I had to make up Dx_gear, Dy_gear, and Dz_gear --
if those are inappropriate, I'd appreciate suggestions for better
names.
It will be necessary to modify the other UIUC configuration files to
include some kind of gear support as well, or the planes will sink
nose-first into the ground down to their CG's (it's actually quite
funny to watch with an external view).
Background
----------
As I frequently remind everyone here, I have no math background worth
spitting at, so I will not even pretend to have done the hard stuff.
The UIUC code uses a copy of a very old version of the LaRCsim
c172_gear.c -- I wanted to update it with Tony Peden's excellent newer
version, which includes differential braking among other goodies (the
UIUC models don't support brakes, period).
I copied the newer code into uiuc_aero.c, and it compiled and ran, but
all of the planes ended up sitting on their tails with their noses in
the air. Since Tony made his gear code nicely parameterized, I
experimented with different values, and found that it wasn't too hard
to balance the Twin Otter by moving the gear back a bit. At first, I
used properties to set different values, but then I decided to
integrate the whole thing properly into the UIUC configuration
framework. Thanks to Tony Peden, who did the real modelling work -- I
can take credit only for two or three hours of integration. It turns
out that Tony's code is generalized enough to deal with a wide range
of different gear structures -- I suspect that it will even work for
the 747, when I get around to trying some values.
LaRCsim c172 on-ground and in-air starts, reset: all work
UIUC Cessna172 on-ground and in-air starts work as expected, reset
results in an aircraft that is upside down but does not crash FG. I
don't know what it was like before, so it may well be no change.
JSBSim c172 and X15 in-air starts work fine, resets now work (and are
trimmed), on-ground starts do not -- the c172 ends up on its back. I
suspect this is no worse than before.
I did not test:
Balloon (the weather code returns nan's for the atmosphere data --this
is in the weather module and apparently is a linux only bug)
ADA (don't know how)
MagicCarpet (needs work yet)
External (don't know how)
known to be broken:
LaRCsim c172 on-ground starts with a negative terrain altitude (this
happens at KPAO when the scenery is not present). The FDM inits to
about 50 feet AGL and the model falls to the ground. It does stay
upright, however, and seems to be fine once it settles out, FWIW.
To do:
--implement set_Model on the bus
--bring Christian's weather data into JSBSim
-- add default method to bus for updating things like the sin and cos of
latitude (for Balloon, MagicCarpet)
-- lots of cleanup
The files:
src/FDM/flight.cxx
src/FDM/flight.hxx
-- all data members now declared protected instead of private.
-- eliminated all but a small set of 'setters', no change to getters.
-- that small set is declared virtual, the default implementation
provided preserves the old behavior
-- all of the vector data members are now initialized.
-- added busdump() method -- FG_LOG's all the bus data when called,
useful for diagnostics.
src/FDM/ADA.cxx
-- bus data members now directly assigned to
src/FDM/Balloon.cxx
-- bus data members now directly assigned to
-- changed V_equiv_kts to V_calibrated_kts
src/FDM/JSBSim.cxx
src/FDM/JSBSim.hxx
-- bus data members now directly assigned to
-- implemented the FGInterface virtual setters with JSBSim specific
logic
-- changed the static FDMExec to a dynamic fdmex (needed so that the
JSBSim object can be deleted when a model change is called for)
-- implemented constructor and destructor, moved some of the logic
formerly in init() to constructor
-- added logic to bring up FGEngInterface objects and set the RPM and
throttle values.
src/FDM/LaRCsim.cxx
src/FDM/LaRCsim.hxx
-- bus data members now directly assigned to
-- implemented the FGInterface virtual setters with LaRCsim specific
logic, uses LaRCsimIC
-- implemented constructor and destructor, moved some of the logic
formerly in init() to constructor
-- moved default inertias to here from fg_init.cxx
-- eliminated the climb rate calculation. The equivalent, climb_rate =
-1*vdown, is now in copy_from_LaRCsim().
src/FDM/LaRCsimIC.cxx
src/FDM/LaRCsimIC.hxx
-- similar to FGInitialCondition, this class has all the logic needed to
turn data like Vc and Mach into the more fundamental quantities LaRCsim
needs to initialize.
-- put it in src/FDM since it is a class
src/FDM/MagicCarpet.cxx
-- bus data members now directly assigned to
src/FDM/Makefile.am
-- adds LaRCsimIC.hxx and cxx
src/FDM/JSBSim/FGAtmosphere.h
src/FDM/JSBSim/FGDefs.h
src/FDM/JSBSim/FGInitialCondition.cpp
src/FDM/JSBSim/FGInitialCondition.h
src/FDM/JSBSim/JSBSim.cpp
-- changes to accomodate the new bus
src/FDM/LaRCsim/atmos_62.h
src/FDM/LaRCsim/ls_geodesy.h
-- surrounded prototypes with #ifdef __cplusplus ... #endif , functions
here are needed in LaRCsimIC
src/FDM/LaRCsim/c172_main.c
src/FDM/LaRCsim/cherokee_aero.c
src/FDM/LaRCsim/ls_aux.c
src/FDM/LaRCsim/ls_constants.h
src/FDM/LaRCsim/ls_geodesy.c
src/FDM/LaRCsim/ls_geodesy.h
src/FDM/LaRCsim/ls_step.c
src/FDM/UIUCModel/uiuc_betaprobe.cpp
-- changed PI to LS_PI, eliminates preprocessor naming conflict with
weather module
src/FDM/LaRCsim/ls_interface.c
src/FDM/LaRCsim/ls_interface.h
-- added function ls_set_model_dt()
src/Main/bfi.cxx
-- eliminated calls that set the NED speeds to body components. They
are no longer needed and confuse the new bus.
src/Main/fg_init.cxx
-- eliminated calls that just brought the bus data up-to-date (e.g.
set_sin_cos_latitude). or set default values. The bus now handles the
defaults and updates itself when the setters are called (for LaRCsim and
JSBSim). A default method for doing this needs to be added to the bus.
-- added fgVelocityInit() to set the speed the user asked for. Both
JSBSim and LaRCsim can now be initialized using any of:
vc,mach, NED components, UVW components.
src/Main/main.cxx
--eliminated call to fgFDMSetGroundElevation, this data is now 'pulled'
onto the bus every update()
src/Main/options.cxx
src/Main/options.hxx
-- added enum to keep track of the speed requested by the user
-- eliminated calls to set NED velocity properties to body speeds, they
are no longer needed.
-- added options for the NED components.
src/Network/garmin.cxx
src/Network/nmea.cxx
--eliminated calls that just brought the bus data up-to-date (e.g.
set_sin_cos_latitude). The bus now updates itself when the setters are
called (for LaRCsim and JSBSim). A default method for doing this needs
to be added to the bus.
-- changed set_V_equiv_kts to set_V_calibrated_kts. set_V_equiv_kts no
longer exists ( get_V_equiv_kts still does, though)
src/WeatherCM/FGLocalWeatherDatabase.cpp
-- commented out the code to put the weather data on the bus, a
different scheme for this is needed.
