This is a sub-system which can be added to any carrier.
These files add a functioning Fresnel Lens Optical Landing System (FLOLS).
The orange/red 'source' lights are illuminated according to the position of
the pilot's eye above/below the 3.5 deg glide slope. The apparent position
of the source light relative to the fixed green datum lights allow the pilot
to 'fly the meatball'. The green 'cut' lights flash when the pilot's eye is
below the coverage of the lowest (red) source light.
TODO - add rules for the operation of the wave-off lights.
Here are files to get automated contrails working. I've set up contrails for
the 737, using my simple, untextured contrail model. Vivian has made another
contrail model, but I'm still trying to get his to work. I'm hoping others
will try to make contrail models also.
Here's some code that defines a top to thermals. When the top of a thermal is
reached the strength is phased-out linearly over the next 100 feet of
altitude. At first I tried just capping the thermal at the top, but the
change in thermal strength was too fast for the FDM to handle well.
Included is a new version of the thermal scenario that includes a top
(height-msl) to the thermal. The default value is 5000 feet.
The calculation of submodel mass from weight has been moved from AIBallistic
to Submodel so that it is calculated only once, rather than on every
iteration as a present. The parameter <contents> has been added, primarily
so that droptanks will have the proper mass. It is the path to an
appropriate property containing a weight in lbs.
Care has to be taken with the use of <contents> because after a reset there
appears to be a delay in submodel instantiation (dt not properly reset???)
and the weight property is not always picked up before it is set to zero in
the key bindings. Slightly hard to explain. It works fine if FGFS has not
been reset though. There is a partial solution which involves the rejigging
of the fuel and gui nasal scripts, but there is still the visible delay in
instantiation to be resolved. I've nearly done the nasal fixes, which will
form part of an update to the Hunter only. I'll probably complete those
later today.
I have added <Cd> and <weight> to the input parameters in the submodels.xml
script. Raw data may be used, thus avoiding the need to guestimate <eda>.
Eda remains, but should now be used to enter the proper cross-sectional
area.
I've added another parameter to the submodel - wind.
It's activated by the entry <wind>true</wind> in the ../submodel.xml file.
If true, the submodel is affected by the local wind, otherwise not. The
parameter defaults to false. This is useful for exhausts and smoke, and
possibly all objects.
Attached are the modified files to add buoyancy as a parameter for a
ballistic object. It may be set by adding
<buoyancy>x</buoyancy> to the submodel .xml file, where x is the appropriate
value (ft per sec2):
32 neutral buoyancy - contrails
>32 positive buoyancy - exhaust plumes
(0 non-op - default value)
If <buoyancy>x</buoyancy> is not used, then there is no effect on the
current ballistic model
Silly me. I was starting the timer at zero, so the first tracer didn't fly
until 0.25 seconds after pulling the trigger. Now the timer starts at the
same value as "delay", so the first round comes out immediately.
Also, I've added an optional configuration attribute that allows you to change
the ballistics of the submodel. This allows parachutes, or anything else
that has ballistics different from a bullet. The attribute is called "eda",
which is the equivalent drag area. Default value is 0.007, which gives the
same ballistics as the current tracers. Increasing this value gives more
drag. A value of 2.0 looks good for a parachute.
math stuff
########################################################################
The deceleration of the ballictic object is now given by:
[ (rho) (Cd) ] / [ (1/2) (m) ] * A * (V * V)
where rho is sea-level air density, and Cd and m are fixed, bullet-like
values. So the calculation is:
0.0116918 * A * (V * V)
The value "A" is what I'm calling the "eda" (equivalent drag area).
########################################################################
A parachute model will have to be built so that the parachutist's feet
are in the forward x-direction.
Here is the submodel.xml config I use for "parachutes":
<submodel>
<name>flares</name>
<model>Models/Geometry/flare.ac</model>
<trigger>systems/submodels/submodel[0]/trigger</trigger>
<speed>0.0</speed>
<repeat>true</repeat>
<delay>0.85</delay>
<count>4</count>
<x-offset>0.0</x-offset>
<y-offset>0.0</y-offset>
<z-offset>-4.0</z-offset>
<yaw-offset>0.0</yaw-offset>
<pitch-offset>0.0</pitch-offset>
<eda>2.0</eda>
</submodel>
Here's some new AI stuff.
1) AI objects must now be defined in a scenario file, not in preferences.xml
or a *-set file. (Of course this doesn't prevent objects from being created
dynamically, as with Durk's traffic manager).
2) A new demo_scenario file is attached. It creates 3 aircraft, a sailboat,
and a thunderstorm.
3) Objects without flightplans live forever.
4) FGAIShip::ProcessFlightplan() is not yet implemented.
5) preferences.xml should now define only <enabled> and <scenario>
First, preferences.xml will define the scenario filename.
For now, the other way of defining ai objects still works, so the sailboat
stays in preferences.xml. Later, I'll move the sailboat into the demo
scenario. If no scenario filename is given, then no scenario will be
processed.
I changed the demo scenario to create two 737's, one takes off on runway 01L,
and the other takes off on runway 01R. This will make a good demo for the ai
system. One problem, if you takeoff on 28L/R right away, you might run into
the taking-off 737's, or be scared.
Here's the newest AI stuff.
The AIManager at init() creates a new scenario. Right now the
default_scenario is hard coded in, but eventually the AIManager should get
the scenario filename from preferences.xml.
The scenario defines which AI objects will be created. Right now it only
creates AIAircraft, but this is easily extended. The scenario also defines
which flightplan will be assigned to the airplane. Scenario config files go
in data/Data/AI.
The Airplane gets a pointer to a FlightPlan object. Each airplane should get
its own flightplan object, even if two airplanes have the same flight plan.
This is because the flightplan maintains the iterator pointing to the
current waypoint, and two airplanes might be at different locations (for
instance if they were created at different times). The flight plan files go
in data/Data/AI/FlightPlans.
When the airplane gets to the waypoint named "END" it vanishes. The
AIAircraft destructor deletes its flight plan (if it has one).
The last waypoint is a place holder only. I called mine
<WPT><NAME>"EOF"</NAME></WPT>.
