OK -- thanks. I have now fixed up all the other XML files in the base
package that use "max" and "wrap". Those affected are all in
Aircraft/Instruments/. In these files I have also corrected the
indentation in some places, and corrected the frequency controls in
nav3.xml (which does not seem to be in use), and corrected a few obvious
hotspot position bugs. Where the radios used wrapping to toggle the
ident button between 0 and 1, I have changed this to use
"property-toggle" instead.
[ In support of the TSR2, SeaHawk and A-10 ]
I've set up some panels, based on the c310 vfr and mini panels. The
vfr panels have a lot of additional instruments on them but impose quite a
high frame-rate hit on my system. The mini panels also have some additional
instruments but seem to work without noticable penalty here. I've set these
panels as the defaults for these aircraft but I'm not sure it's a good idea
to have the vfr panels by default due to the performance hit. Using them as
default will should give some feedback though;)
To go with the new panels are a number of rough and ready instruments I
hacked, mostly out of one of the rpm gauges, but I've adapted the throttle
quadrent (jet-throttle-quadrant) to funstion for throttle, flaps and reheat.
All the gauge faces were based on an existing ffgfs instrument texture, so
there's no problem with copyright there. All the other bits that I've done
may be distributed under the same conditions as fgfs.
you simply click with the left mouse button to advance to 'both';
after that, if you click again, the start engages until you let go of
the mouse button, at which point the knob snaps back to 'both'.
- makes instrument knobs turn at a realistic rate
- removes redundant <min> and <max> specifications*
- corrects the indentation to reflect nesting depth
- corrects some descriptive names
* E.g. if the gyro compass heading is 365, there's no point clamping the
value to 360 before drawing it. Just using the given value is more
likely to be right - or, if it's wrong, at least we won't hide the bug.
button) modes. Due to a typo in altimeter.xml, one direction of
adjustment with the left mouse button was giving fast changes.
Simple patch attached.
- Julian
twice the design size (character height) of the old one.
Advantages:
- displays . and : correctly with less space around, and digits
with more space around (using Andy's improvements to plib)
- small text becomes much more legible (-> clock, AP-altitude)
- the font contains pretty much every character that can be
displayed on a seven segment display, so it might be more
useful for future instruments.
It's a little funky to use right now because
the FRQ and timer buttons should be momentary action.
As it stands you need to do 2 clicks to send on/off.
If anybody can think of a workaround, we could use one.
For now the ADF and BFO buttons just toggle the
annunciators. For ANT mode, I just need to wire up the
ADF needle.
Two clicks on FRQ flip flops the selected and standby
freqs.
Two clicks of FLT/ET will change the standby display
to timer mode and another two will flip between
FLT and ET. If you click and the annunciator flashes
briefly but the display does not change, you need
to click FRQ -one time- to get the button in phase.
ET mode has a count down mode, this is where it really gets tricky.
On the real thing, you hold the SET/RST button for 2 seconds.
Here you must click one time, wait for the display to flash then
click one more time. Now you can set the time to count down.
Right clicking the dial will set minutes, middle click (I know,
I'll make it a keyboard modifier later) sets hours. As usual
the left side decreases and right side increases.
Once you have the desired time set, click the SET/RST button
twice in rapid succession. Two rapid clicks will reset the
elapsed timer when it's counting down, but also while you are
setting it (when display is flashing).
When the count down timer reaches zero, it starts counting up again.
It -should- flash for 15 seconds and set off a warning tone, but
for now it doesn't.
The unit is also equipped with an on/off/volume knob. Whne the
unit is powered down the timers are reset.
TODO:
Add labeling
Wire up ADF needle
Prettier face
Since a while I get a line of black pixel garbage below the labels "WL" and
"ALT" on the autopilot. Does anybody else see this? (Or is it a feature of
my graphics card? :-) The following patch fixes this for me.
