1
0
Fork 0
fgdata/Docs/README.digitalfilters
Stuart Buchanan c974f5242d Clean up README files.
- Remove trailing whitespace
- Replace tabs with spaces
- Reformat to < 85 characters to avoid autogenerate readme.pdf bleeding over
  margins.
2013-06-20 23:02:17 +01:00

453 lines
18 KiB
Text

COMMON SETTINGS
==============================================================================
Currently four types of digital filter implementations are supported. They all
serve an individual purpose or are individual implementations of a specific
filter type. Each filter implementation uses the same set of basic configuration
tags and individual configuration elements. These individual elements are
described in the section of the filter.
The InputValue
==============================================================================
Each filter has several driving values, like the input value itself, sometimes
a reference value, a gain value and others. Most of these input values can be
either a constant value or the value of a property. They all use the same syntax
and will be referred to as InputValue in the remaining document.
The complete XML syntax for a InputValue is
<some-element>
<condition>
<!-- any condition as defined in README.conditions -->
</condition>
<property>/some/property/name</property>
<value>0.0</value>
<scale>1.0</value>
<offset>0.0</offset>
<max>infinity</max>
<min>-infinity<min>
<abs>false</abs>
<period>
<min>-180.0</min>
<max>-180.0</max>
</period>
</some-element>
The enclosing element <some-element> is the element defined in each filter, like
<input>, <u_min>, <reference> etc. These elements will be described later.
The value of the input is calculated based on the given value, scale and offset as
value * scale + offset
and the result is clipped to min/max, if given.
With the full set of given elements, the InputValue will initialize the named
property to the value given, reduced by the given offset and reverse scaled by
the given scale.
Example:
<input>
<property>/controls/flight/rudder</property>
<value>0.0</value>
<scale>0.5</scale>
<offset>0.5</offset>
</input>
Will use the property /controls/flight/rudder as the input of the filter. The
property will be initialized at a value of zero and since the property usually is
in the range [-1..+1], the the value of <input> will be in the range
(-1)*0.5+0.5 to (+1)*0.5+0.5 which is [0..1].
The default values for elements not given are:
<value/> : 0.0
<scale/> : 1.0
<offset/>: 0.0
<property/> : none
<min/> : unclipped
<max/> : unclipped
<abs/> : false
Some examples:
<input>
<property>/position/altitude-ft</property>
<scale>0.3048</scale>
</input>
Gives the altitude in meters. No initialization of the property is performed, no
offset applied.
<reference>
<value>0.0</value>
</reference>
A constant reference of zero.
A abbreviated method of defining values exist for using a just constant or a
property. The above example may be written as
<reference>0.0</reference>
Or if the reference is defined in a property
<reference>/some/property/name</reference>
No initialization, scaling or offsetting is performed here.
The logic behind this is: If the text node in the element (the text between the
opening and closing tag) can be converted to a double value, it will be interpreted
as a double value. Otherwise the text will
be interpreted as a property name.
Examples:
<reference>3.1415927</reference> - The constant of PI (roughly)
<reference>/position/altitude-ft</reference> - The property /position/altitude-ft
<reference>3kings</reference> - The constant 3. The word kings is
ignored
<reference>food4less</reference> - The property food4less
The <property> element may also be written as <prop> for backward compatibility.
There may be one or more InputValues for the same input of a filter which may be
bound to conditions. Each InputValue will have its condition checked in the order
of InputValues given in the configuration file. The first InputValue that returns
true for its condition will be evaluated. Chaining a number of InputValues with
conditions and an unconditioned InputValue works like the C language equivalent
if( condition ) {
// compute value of first element
} else if( condition2 ) {
// compute value of second element
} else if( condition3 ) {
// compute value of third element
} else {
// compute value of last element
}
Example: Set the gain to 3.0 if /autopilot/locks/heading equals dg-heading-hold or
2.0 otherwise.
<digital-filter>
<gain>
<condition>
<equals>
<property>/autopilot/locks/heading</property>
<value>dg-heading-hold</value>
</equals>
</condition>
<value>3.0</value>
<gain>
<!-- Hint: omit a condition here as a fallthru else condition -->
</gain>
<value>2.0</value>
<gain>
<digital-filter>
If the element <abs> is used and set to the value "true", only the absolute
value of the input (the positive part) is used for further computations. The
abs function is applied after all other computations are completed.
OutputValue
==============================================================================
Each filter drives one to many output properties. No scaling or offsetting is
implemented for the output value, these should be done in the filter itself.
The output properties are defined in the <output/> element by adding <property/>
elements within the <output/> element. For just a single output property, the
<property/> element may be ommited. For backward compatibility, <property/> may
be replaced by <prop/>. Non-existing properties will be created with type double.
Example: (Multiple output properties)
<output>
<property>/some/output/property</property>
<property>/some/other/output/property</property>
<property>/and/another/output/property</property>
</output>
Example: a single output property
<output>/just/a/single/property</output>
Other Common Settings
==============================================================================
<name> String The name of the filter. Used for debug purpose.
Example:
<name>pressure rate filter</name>
<debug> Boolean If true, this filter puts out debug information when
updated. Example: <debug>false</debug>
<input> InputValue The input property driving the filter.
Refer to InputValue for details.
<reference> InputValue The reference property for filter that need one.
Refer to InputValue for details.
<output> Complex Each filter can drive one to many output properties.
Refer to OutputValue for details.
<u_min> InputValue This defines the optional minimum and maximum value the
<u_max> output is clamped to. If neither <u_min> nor <u_max>
exists, the output is only limited by the internal limit
of double precision float computation. If either <u_min>
or <u_max> is given, clamping is activated. A missing min
or max value defaults to 0 (zero).
Note: <u_min> and <u_max> may also occour within a <config>
element. <min> and <max> may be used as a substitude for
the corresponding u_xxx element.
<period> Complex Define a periodical input or output value. The phase width
is defined by the child elements <min> and <max> which are
of type InputValue
Example: Limit the pilot's body temperature to a constant minimum of 36 and a
maximum defined in /pilots/max-body-temperature-degc, initialized to 40.0
<u_max>
<prop>/pilots/max-body-temperature-degc</prop>
<value>40.0</
</u_max>
<min>
<value>36.0</value>
</min
Implicit definition of the minimum value of 0 (zero) and defining a maximum of 100.0
<config>
<u_max>100.0</u_max>
</config>
This defines the input or output as a periodic value with a phase width of 360, like
the compass rose. Any value reaching the filter's input or leaving the filter at the
output will be transformed to fit into the given range by adding or substracting one
phase width of 360. Values of -270, 90 or 450 applied to this periodical element will
always result in +90. A value of 630, 270 or -90 will be normalized to -90 in the
given example.
<period>
<min>-180.0</min>
<max>180.0</max>
</period>
<enable> Complex Define a condition to enable or disable the filter. For
disabled filters, no output computations are performed.
Only enabled filters fill the output properties. The
default for undefined conditions is enabled.
Several way exist to define a condition. The most simple
case is checking a boolean property. For this, just a
<prop> element naming this boolean property is needed.
The boolean value of the named property defines the
enabled state of the filter. To compare the value of a
property with a constant, a <prop> and a <value> element
define the property name and the value to be compared.
The filter is enabled, if the value of the property equals
the given value. A case sensitive string compare is
performed here.
To define more complex conditions, a <condition> element
may be used to define any condition described in
README.conditions. If a <condition> element is present
and if it contains a valid condition, this conditions has
precedence over a given <prop>/<value> condition.
The child element <honor-passive>, a boolean flag, may be
present within the <enable> element. If this element is
true, the property /autopilot/locks/passive-mode is checked
and if it is true, the filter output is computed, but the
output properties are not set. The default for
honor-passive is false
Example: Check a boolean property, only compute this filter if gear-down is true and
/autopilot/locks/passive-mode is false
<enable>
<prop>/gear/gear-down</prop>
<honor-passive>true</honor-passive>
</enable>
Check a property for equality, only compute this filter if the autopilot is locked
in heading mode.
<enable>
<prop>/autopilot/locks/heading</prop>
<value>dg-heading-hold</value>
</enable>
Use a complex condition, only compute this filter if the autopilot is serviceable
and the lock is either dg-heading-hold or nav1-heading-hold
<enable>
<condition>
<property>/autopilo/serviceable</property>
<or>
<equals>
<property>/autopilot/locks/heading</property>
<value>dg-heading-hold</value>
</equals>
<equals>
<property>/autopilot/locks/heading</property>
<value>nav1-heading-hold</value>
</equals>
</or>
</condition>
</enable>
INDIVIDUAL FILTER CONFIGURATION
==============================================================================
Digital Filter
Six different types of digital filter can be configured inside the autopilot
configuration file. There are four low-pass filter types and two gain filter
types.
The low-pass filter types are:
* Exponential
* Double exponential
* Moving average
* Noise spike filter
The gain filter types are:
* gain
* reciprocal
To add a digital filter, place a <filter> element under the root element. Next to
the global configuration elements described above, the following elements configure
the digital filter:
<filter-time> InputValue This tag is only applicable for the exponential and
double-exponential filter types. It controls the
bandwidth of the filter. The bandwidth in Hz of the
filter is: 1/filter-time. So a low-pass filter with a
bandwidth of 10Hz would have a filter time of 1/10 = 0.1
<samples> InputValue This tag only makes sense for the moving-average filter.
It says how many past samples to average.
<max-rate-of-change>
InputValue This tag is applicable for the noise-spike filter.
It says how much the value is allowed to change per
second.
<gain> InputValue This is only applicable to the gain and reciprocal filter
types. The output for gain filter is computed as input*gain
while the reciprocal filter computes output as gain/input
for input values != 0 (zero). Gain may be a constant, a
property name defined by a <prop> element within the <gain>
element or a property name initialized to a value by using
a <prop> and <value> element.
Example: a pressure-rate-filter implemented as a double exponential low pass filter
with a bandwith of 10Hz
<filter>
<name>pressure-rate-filter</name>
<debug>false</debug>
<type>double-exponential</type>
<enable>
<prop>/autopilot/locks/pressure-rate-filter</prop>
<value>true</value>
</enable>
<input>/autopilot/internal/pressure-rate</input>
<output>/autopilot/internal/filtered-pressure-rate</output>
<filter-time>0.1</filter-time>
</filter>
This will filter the pressure-rate property. The output will be to a new
property called filtered-pressure-rate. You can select any numerical property
from the property tree. The input property will not be affected by the filter,
it will stay the same as it would if no filter was configured.
Example 2:
<filter>
<name>airspeed elevator-trim gain reciprocal filter</name>
<debug>false</debug>
<enable>
<prop>/autopilot/locks/airspeed-elevator-trim-gain</prop>
<value>true</value>
</enable>
<type>reciprocal</type>
<gain>
<prop>/autopilot/settings/elevator-trim-airspeed-reciprocal-gain</prop>
<value>7</value>
</gain>
<input>/velocities/airspeed-kt</input>
<output>/autopilot/internal/elevator-trim-gain</output>
<u_min>0.005</u_min>
<u_max>0.02</u_max>
</filter>
This will use the /velocities/airspeed-kt property to produce a gain factor
that reduces as airspeed increases. At airspeeds up to 350kt the gain will
be clamped to 0.02, at 700kt the gain will be 0.01 and at 1400kt the gain will
be 0.005. The gain will be clamped to 0.005 for airspeeds > 1400kt.
The output from this filter could then be used to control the gain in a PID
controller:
<pid-controller>
<name>Pitch hold</name>
<debug>false</debug>
<enable>
<prop>/autopilot/locks/pitch</prop>
<value>true</value>
</enable>
<input>
<prop>/orientation/pitch-deg</prop>
</input>
<reference>
<prop>/autopilot/settings/target-pitch-deg</prop>
</reference>
<output>
<prop>/autopilot/internal/target-elevator-trim-norm</prop>
</output>
<config>
<Ts>0.05</Ts>
<Kp>
<prop>/autopilot/internal/elevator-trim-gain</prop>
<value>0.02</value>
</Kp>
<beta>1.0</beta>
<alpha>0.1</alpha>
<gamma>0.0</gamma>
<Ti>2.0</Ti>
<Td>0.2</Td>
<u_min>-1.0</u_min>
<u_max>1.0</u_max>
</config>
</pid-controller>
IMPORTANT NOTE: The <Kp> tag in PID controllers has been revised to operate in
the same way as the <gain> elements in filters. However, the original format
of <Kp> will continue to function as before i.e. <Kp>0.02</Kp> will specify a
fixed and unalterable gain factor, but a warning message will be output.
The gain type filter is similar to the reciprocal filter except that the gain
is applied as a simple factor to the input.
-------------------------------------------------------------------------------
Parameters
<name> The name of the filter. Give it a sensible name!
<debug> If this tag is set to true debugging info will be printed on the
console.
<enable> Encloses the <prop> and <value> tags which are used to enable or
disable the filter. Instead of the <prop> and <value> tags, a <condition>
tag may be used to define a condition. Check README.conditions for more
details about conditions. Defaults to enabled if unspecified.
<type> The type of filter. This can be exponential, double-exponential,
moving-average, noise-spike, gain or reciprocal.
<input> The input property to be filtered. This should of course be a
numerical property, filtering a text string or a boolean value does not make
sense.
<output> The filtered value. You can make up any new property.
<u_min> The minimum output value from the filter. Defaults to -infinity.
<u_max> The maximum output value from the filter. Defaults to +infinity.
These are the tags that are applicable to all filter types. The following tags
are filter specific.
<filter-time> This tag is only applicable for the exponential and
double-exponential filter types. It controls the bandwidth of the filter. The
bandwidth in Hz of the filter is: 1/filter-time. So a low-pass filter with a
bandwidth of 10Hz would have a filter time of 1/10 = 0.1
<samples> This tag only makes sense for the moving-average filter. It says how
many past samples to average.
<max-rate-of-change> This tag is applicable for the noise-spike filter. Is
says how much the value is allowed to change per second.
<gain> This, and it's enclosed <prop> and <value> tags, are only applicable to
the gain and reciprocal filter types. The <prop> tag specifies a property node
to hold the gain value and the <value> tag specifies an initial default value.
The gain defaults to 1.0 if unspecified.
The output from the gain filter type is: input * gain.
The output from the reciprocal filter type is: gain / input.
The gain can be changed during run-time by updating the value in the property
node.