The comm radio knobs are screwed. Left half increase, right half decrease.
Fixed that. (I wonder since when this is broken. Does nobody use it?)
To reproduce: $ fgfs --aircraft=c310
The c310's adf needle (HSI) doesn't work. The hsi.xml instrument does
still use the old property. The fix didn't have negative effects on
other a/c that I had tested.
Changes made 19/12/2004
Panel re-oriented
3d Compass shows through windows.
Wing-tips slightly altered.
Changes made 18/12/2004
Prop spinner shortened and widened
Nose area slightly remodelled to fit silouette
Nose texture altered to place lower intake correctly
Nose wheel reduced in size.
Nose leg Oleo guide added (does not rotate - is this correct with real ac?)
Nose wheel Axle added.
Nose wheel fixed to rotate about it's shaft axis.
Windscreen / panel mesh changed so that panel no longer protrudes thru dash
Panel instruments moved to represent the geometries of the real cockpit.
Pilot / Copilot Yokes moved inboard to represent the geometries of the real cockpit.
Alpha layer added to interior texture to prevent panel showing through seats / yokes.
Interior texture duplicated and mapped to panel only to allow panel to show.
Front seats moved slightly inboard.
Landing light pair added to port wing texture.
Alpah layer added to wing texture to prevent panel showing through.
Texture remapped to Flaps (no shows ribs again).
Wing strut outer joins brought inboard to point of wing taper to match real aircraft geometries.
Wing struts thinned in front profile and thickened in side profile.
VHF aerials moved aft to their usual position.
Maingear legs altered so they now join with the fusealage (previously, 20cm gap)
Rear window altered slightly to match silouette.
Rear (white) Navigation Light made to translate with the rudder.
Not yet done: independant landing and taxi lights on port wing
I've finished the emigration of the radiostack, and I've also removed it
completely. It turned out that the comm radio is completely implemented in
the ATC subsystem. I've changed the affected ATC files to point
to /instrumentation/com, but I guess that the maintainer of the ATC code
should decide wether to make it configureable, and how.
I also had to change some files in Network and Main. The changes in network
should be obvious, but the changes in Main were a bit suspect. The files
included radiostack.hxx, but they weren't directly depending on
radiostack-hxx. They were depending on other files that were included by
radiostack.hxx. I got it to compile, but I'm not sure if I included the
correct directly depending file.
For the data directory I changed every occurrence of /radios/
with /instrumentation/ with this simple one-liner that I found on the net:
find -name '*.xml' -type f | xargs perl -pi -e
's/\/radios\//\/instrumentation\//g'
Instead of me sending all the files that got changed by this I suggest that
you execute the one-liner yourself. Of course I can not guarantee that this
will work perfectly, but I considered hand editing to be not an option (I'm
lazy). I don't want to test every aircraft to see if everything still works,
I think it's better to wait and see if anyone complaints about broken nav
radios/instruments.
I've made an encoder and a transponder. The transponder gets C-Mode altitude
information from the encoder. These two might not be very usefull right now,
but I think they might come in handy when the ATC network gets going.
Here are some updates to the KAP140 autopilot in the default c172. It now uses
ailerons and elevator instead of aileron-trim and elevator-trim. I've started
to "upgrade" it to the "two axis altitude preselect" version. Vertical speed
select rounds to nearest 100 fpm.
I've also modified the c172 electrical configuration to turn on the gps
instrument.
Perhaps the most important change is that the nasal script for the KAP140 has
moved from data/Nasal to the c172p aircraft subdir. So it is important that
you delete data/Nasal/kap140.nas. Having the kap140.nas script as a global
script was not a good solution. Now it is aircraft specific, and thus
included in the c172p-set.xml file. Ideally I would like it to be instrument
specific, so that it would be included whenever the KAP140*.xml instruments
where included on the panel.
Instrumentation and systems are now configureable from xml files. The two
generic configurations generic-systems.xml and generic-instrumentation.xml
configures the systems and instrumentation as it was hardcoded. You can
override the generic configurations in a similar way as you override the
autopilot configuration.
All necessary elements for an ADF gauge had been migrated from
Cockpit/kr_87.cxx to Instrumentation/adf.cxx. Migrating the sound
related elements was apparently planned, but not done yet. This
intermediate state broke the ident morse sound: it couldn't get
turned off and it always indicated "SF", regardless of the tuned-in
frequency. The following patches continue the migration:
adf-radio.diff => Base/Aircraft/Instruments/adf-radio.xml:
---------------------------------------------------------------
* sets maximum volume to 1 (rather than 2); Not only is 1
loud enough (and 2 unpleasantly noisy), it also prevents
the knob from being turned to non-existant positions. :-)
* fixes wrong use of /instrumentation/adf/ident
* the voice/ident selector(?) remains unchanged, but as it's
not switched to "IDENT", there'll be no ident sound by default
this is consistent with other sounds and DME.
radiostack.diff => src/Cockpit/radiostack.[ch]xx:
---------------------------------------------------------------
* comment out use of FGKR_87 class. kr_87.[ch]xx is now no
longer used. kr-87adf.xml would no longer work, either, but
isn't used anywhere, anyway. Future adf radios have to use
the adf instrument, using xml/Nasal for specific hardware
implementation details.
adf.diff => src/Instrumentation/adf.[ch]xx:
---------------------------------------------------------------
* adds ident morse sound capability using two new input
properties:
- /instrumentation/adf/volume-norm (double)
- /instrumentation/adf/ident-audible (bool)
Here's some new AI stuff.
1) AI objects must now be defined in a scenario file, not in preferences.xml
or a *-set file. (Of course this doesn't prevent objects from being created
dynamically, as with Durk's traffic manager).
2) A new demo_scenario file is attached. It creates 3 aircraft, a sailboat,
and a thunderstorm.
3) Objects without flightplans live forever.
4) FGAIShip::ProcessFlightplan() is not yet implemented.
5) preferences.xml should now define only <enabled> and <scenario>
Here is the KAP140 Two Axis Autopilot update.
I think it's fairly complete now, all the modes are working. I tested the
localizer and glideslope hold and it was pretty stable all the way down to
the middle marker.
In the pilot guide for backcourse hold (REV) mode it says to reset the heading
bug to the _front course_. I haven't figured out how to implement this so for
the time beeing one should reset the heading bug to the _backcourse_. Apart
from this the panel should operate identical to the way the pilot guide
describes.
Here is the KAP140 Two Axis Autopilot.
Aircraft/Instruments/KAP140TwoAxis.xml
Is of course the instrument config file.
Aircraft/Instruments/Textures/KAP140.rgb
The texture.
Nasal/kap140.nas
Most of the work is done here. Without Nasal I don't see how I could implement
the NAV-ARM modes and the flashing annunciators.
Aircraft/c172p/Systems/KAP140.xml
The autopilot PID controllers configuration file. Maybe this file should be in
a more accessible directory and not hidden deep inside c172p!?
I've also attached the changes to the default C172 to include this autopilot
in the 3d-cockpit panel and the 2d vfr panel. Or at least I hope that I've
managed to include all that is needed.
