I've made an encoder and a transponder. The transponder gets C-Mode altitude
information from the encoder. These two might not be very usefull right now,
but I think they might come in handy when the ATC network gets going.
Here are some updates to the KAP140 autopilot in the default c172. It now uses
ailerons and elevator instead of aileron-trim and elevator-trim. I've started
to "upgrade" it to the "two axis altitude preselect" version. Vertical speed
select rounds to nearest 100 fpm.
I've also modified the c172 electrical configuration to turn on the gps
instrument.
Perhaps the most important change is that the nasal script for the KAP140 has
moved from data/Nasal to the c172p aircraft subdir. So it is important that
you delete data/Nasal/kap140.nas. Having the kap140.nas script as a global
script was not a good solution. Now it is aircraft specific, and thus
included in the c172p-set.xml file. Ideally I would like it to be instrument
specific, so that it would be included whenever the KAP140*.xml instruments
where included on the panel.
Instrumentation and systems are now configureable from xml files. The two
generic configurations generic-systems.xml and generic-instrumentation.xml
configures the systems and instrumentation as it was hardcoded. You can
override the generic configurations in a similar way as you override the
autopilot configuration.
All necessary elements for an ADF gauge had been migrated from
Cockpit/kr_87.cxx to Instrumentation/adf.cxx. Migrating the sound
related elements was apparently planned, but not done yet. This
intermediate state broke the ident morse sound: it couldn't get
turned off and it always indicated "SF", regardless of the tuned-in
frequency. The following patches continue the migration:
adf-radio.diff => Base/Aircraft/Instruments/adf-radio.xml:
---------------------------------------------------------------
* sets maximum volume to 1 (rather than 2); Not only is 1
loud enough (and 2 unpleasantly noisy), it also prevents
the knob from being turned to non-existant positions. :-)
* fixes wrong use of /instrumentation/adf/ident
* the voice/ident selector(?) remains unchanged, but as it's
not switched to "IDENT", there'll be no ident sound by default
this is consistent with other sounds and DME.
radiostack.diff => src/Cockpit/radiostack.[ch]xx:
---------------------------------------------------------------
* comment out use of FGKR_87 class. kr_87.[ch]xx is now no
longer used. kr-87adf.xml would no longer work, either, but
isn't used anywhere, anyway. Future adf radios have to use
the adf instrument, using xml/Nasal for specific hardware
implementation details.
adf.diff => src/Instrumentation/adf.[ch]xx:
---------------------------------------------------------------
* adds ident morse sound capability using two new input
properties:
- /instrumentation/adf/volume-norm (double)
- /instrumentation/adf/ident-audible (bool)
Here's some new AI stuff.
1) AI objects must now be defined in a scenario file, not in preferences.xml
or a *-set file. (Of course this doesn't prevent objects from being created
dynamically, as with Durk's traffic manager).
2) A new demo_scenario file is attached. It creates 3 aircraft, a sailboat,
and a thunderstorm.
3) Objects without flightplans live forever.
4) FGAIShip::ProcessFlightplan() is not yet implemented.
5) preferences.xml should now define only <enabled> and <scenario>
Here is the KAP140 Two Axis Autopilot update.
I think it's fairly complete now, all the modes are working. I tested the
localizer and glideslope hold and it was pretty stable all the way down to
the middle marker.
In the pilot guide for backcourse hold (REV) mode it says to reset the heading
bug to the _front course_. I haven't figured out how to implement this so for
the time beeing one should reset the heading bug to the _backcourse_. Apart
from this the panel should operate identical to the way the pilot guide
describes.
Here is the KAP140 Two Axis Autopilot.
Aircraft/Instruments/KAP140TwoAxis.xml
Is of course the instrument config file.
Aircraft/Instruments/Textures/KAP140.rgb
The texture.
Nasal/kap140.nas
Most of the work is done here. Without Nasal I don't see how I could implement
the NAV-ARM modes and the flashing annunciators.
Aircraft/c172p/Systems/KAP140.xml
The autopilot PID controllers configuration file. Maybe this file should be in
a more accessible directory and not hidden deep inside c172p!?
I've also attached the changes to the default C172 to include this autopilot
in the 3d-cockpit panel and the 2d vfr panel. Or at least I hope that I've
managed to include all that is needed.
Add clickable range selection for the radar and wxradar. Right
now it is clickable only between 20 and 40 mile ranges, which should work for
most uses.
OV10-jsbsim-set.xml has many changes. It creates a thunderstorm over
woodside VOR. It removes the lowest cloud layer so that the storm can be
seen. It sets the surface wind speed to zero, which may help stop the
"drifting left" complaints. It sets the radar range to 40 miles.
The weather radar instrument is corrected.
The radar instrument uses the above three items, and applies a scale factor to
the x-shift and y-shift in order to match the instrument's scale. Changing
the display scale can be done entirely in the XML code for the instrument.
Right now it's set up only to display a 40 mile scale.
The radar is an AWACS view, which is not very realistic, but it is useful and
demonstrates the technology. With just a little more work I can get a HUD
marker. All I need to do there is make a bank angle adjustment to the
current values.
This works great with one target. For two or more targets the radar
instrument will have to know the numbering of the aircraft model properties.
This isn't implemented yet.
David Culp:
I couldn't stop. Here's a better radar instrument. It has:
1) range select knob 20 and 40 nm (not clickable.. yet)
2) target altitude readout at lower right
3) target disappears when range exceeds 43 nm
4) range ring values now are read from instrumentation/radar/range
5) instrumentation/radar/range is preset in the *-set.xml file to 40 nm
The next step would be a clickable range selection. The problem here is that
the instrument currently displays the "blip" only if the target's range is
less then 43 nm. If the range scale is decreased to 20 nm, then the "blip"
will show past the edges of the instrument. I might need to make another
instrument for the 20 nm scale to make that work.
tasks that should be purely proportional. So I added support for my old
ultra-simplistic PI controller. This does wonders for stage #1 of the
altitude and AGL hold.
controls in the cockpit vs. which wheels they apply to. FlightGear now
sets /controls/gear/brake-left, /controls/gear/brake-right, and
/controls/gear/brake-parking. It should be up to the FDM to sort out
which wheels under which circumstances are affected by these controls
and ultimately what happens to the physical motion of the aircraft.
I added some more hotspots to Davids c172p since he already had done all the animation. Also I tried making the throttle and mixture knobs into hotspots even when they are moving adding extra hotspots for them. Also you can click on the trim wheel to trim now.
I added a directory for the labels for the white toggle switches, but there is probably better way to do the labels then I came up with. There is a short readme file which gives the path for the new directory.
