Changes made 19/12/2004
Panel re-oriented
3d Compass shows through windows.
Wing-tips slightly altered.
Changes made 18/12/2004
Prop spinner shortened and widened
Nose area slightly remodelled to fit silouette
Nose texture altered to place lower intake correctly
Nose wheel reduced in size.
Nose leg Oleo guide added (does not rotate - is this correct with real ac?)
Nose wheel Axle added.
Nose wheel fixed to rotate about it's shaft axis.
Windscreen / panel mesh changed so that panel no longer protrudes thru dash
Panel instruments moved to represent the geometries of the real cockpit.
Pilot / Copilot Yokes moved inboard to represent the geometries of the real cockpit.
Alpha layer added to interior texture to prevent panel showing through seats / yokes.
Interior texture duplicated and mapped to panel only to allow panel to show.
Front seats moved slightly inboard.
Landing light pair added to port wing texture.
Alpah layer added to wing texture to prevent panel showing through.
Texture remapped to Flaps (no shows ribs again).
Wing strut outer joins brought inboard to point of wing taper to match real aircraft geometries.
Wing struts thinned in front profile and thickened in side profile.
VHF aerials moved aft to their usual position.
Maingear legs altered so they now join with the fusealage (previously, 20cm gap)
Rear window altered slightly to match silouette.
Rear (white) Navigation Light made to translate with the rudder.
Not yet done: independant landing and taxi lights on port wing
I've finished the emigration of the radiostack, and I've also removed it
completely. It turned out that the comm radio is completely implemented in
the ATC subsystem. I've changed the affected ATC files to point
to /instrumentation/com, but I guess that the maintainer of the ATC code
should decide wether to make it configureable, and how.
I also had to change some files in Network and Main. The changes in network
should be obvious, but the changes in Main were a bit suspect. The files
included radiostack.hxx, but they weren't directly depending on
radiostack-hxx. They were depending on other files that were included by
radiostack.hxx. I got it to compile, but I'm not sure if I included the
correct directly depending file.
For the data directory I changed every occurrence of /radios/
with /instrumentation/ with this simple one-liner that I found on the net:
find -name '*.xml' -type f | xargs perl -pi -e
's/\/radios\//\/instrumentation\//g'
Instead of me sending all the files that got changed by this I suggest that
you execute the one-liner yourself. Of course I can not guarantee that this
will work perfectly, but I considered hand editing to be not an option (I'm
lazy). I don't want to test every aircraft to see if everything still works,
I think it's better to wait and see if anyone complaints about broken nav
radios/instruments.
Here are some updates to the KAP140 autopilot in the default c172. It now uses
ailerons and elevator instead of aileron-trim and elevator-trim. I've started
to "upgrade" it to the "two axis altitude preselect" version. Vertical speed
select rounds to nearest 100 fpm.
I've also modified the c172 electrical configuration to turn on the gps
instrument.
Perhaps the most important change is that the nasal script for the KAP140 has
moved from data/Nasal to the c172p aircraft subdir. So it is important that
you delete data/Nasal/kap140.nas. Having the kap140.nas script as a global
script was not a good solution. Now it is aircraft specific, and thus
included in the c172p-set.xml file. Ideally I would like it to be instrument
specific, so that it would be included whenever the KAP140*.xml instruments
where included on the panel.
Here is the KAP140 Two Axis Autopilot update.
I think it's fairly complete now, all the modes are working. I tested the
localizer and glideslope hold and it was pretty stable all the way down to
the middle marker.
In the pilot guide for backcourse hold (REV) mode it says to reset the heading
bug to the _front course_. I haven't figured out how to implement this so for
the time beeing one should reset the heading bug to the _backcourse_. Apart
from this the panel should operate identical to the way the pilot guide
describes.
Here is the KAP140 Two Axis Autopilot.
Aircraft/Instruments/KAP140TwoAxis.xml
Is of course the instrument config file.
Aircraft/Instruments/Textures/KAP140.rgb
The texture.
Nasal/kap140.nas
Most of the work is done here. Without Nasal I don't see how I could implement
the NAV-ARM modes and the flashing annunciators.
Aircraft/c172p/Systems/KAP140.xml
The autopilot PID controllers configuration file. Maybe this file should be in
a more accessible directory and not hidden deep inside c172p!?
I've also attached the changes to the default C172 to include this autopilot
in the 3d-cockpit panel and the 2d vfr panel. Or at least I hope that I've
managed to include all that is needed.
I added some more hotspots to Davids c172p since he already had done all the animation. Also I tried making the throttle and mixture knobs into hotspots even when they are moving adding extra hotspots for them. Also you can click on the trim wheel to trim now.
I added a directory for the labels for the white toggle switches, but there is probably better way to do the labels then I came up with. There is a short readme file which gives the path for the new directory.
Make the plane much sloppier at high alpha and/or with the flaps
extended. In slow flight, there's much more lateral instability now,
and adverse yaw is more obvious at the start of a turn using only
ailerons.
activated with the mouse, but they do respond to the following
properties:
/controls/lights/taxi
/controls/lights/landing
/controls/pitot-heat
/controls/lights/navigation
/controls/lights/beacon
/controls/lights/strobes
- yokes
- carb heat
- throttle
- mixture
- flap switch
- trim wheel
Moved the pilot seat back slightly.
Use LOD more aggressively, so that all the interior detail is skipped
when the viewer is distant.
